background image

8100/8200 Monitor Instruction Manual

2  Installation

2.1  Location

The 8100/8200 Monitor is housed in an IP65 enclosure and is therefore suitable for field mounting. It is advisable to 
mount the monitor in a location that has some protection from the environment; this could be a GRP/metal cabinet, in 
a central room or the use of a protective shield. Suitable enclosures can be provided by Partech.

2.2  Mounting Options

A range of mounting options are available for the 8100/8200 Monitors, which will allow the user to install the sensor in 
a wide variety of locations.

The 8100/8200 Monitor is designed so that it can be surface mounted, the hole positions required for this are shown 
below.

Mounting hardware such as handrail brackets, protective hoods and sensor brackets are available from Partech. The 
8200 Monitor using the standard bracket (Part Number 171280) is shown above.

When mounting the sensor and monitor it is recommended that the two entities be kept as close together as possible 
so that the calibration process is simplified.  The sensors are supplied with a standard length of 10 metres of cable, 
though this can be increased on request to a maximum of 100 metres. The cable can be extended using a junction 
box and good quality instrument cable (3-core minimum).

168270IM-02 Issue Date 05/01/2010

Page 6 of 14

75.50

75.50

5.00

5.00 DIA

6.00

1

2

0

.0

0

Содержание 8100















Отзывы: