Parsun F60 BEL-D Скачать руководство пользователя

Страница: 69 / 112

Locking torque: First time 6 Nm
Second time 17 Nm

Remove the connecting rod and measure the width of the plastic clearance gauge after

being compressed. If the specified value is exceeded, replace the connecting rod bearing
bush.

Oil clearance: 0.020~0.052mm

Note:

Do not turn the connecting rod until the measurement is completed

Clearance between main journal and oil

Clean the mounting surface of bearing bush, main journal, motor body and engine base.

Install the bearing bush and crankshaft to the body.

Place a plastic clearance gauge on the main journal and make it parallel to the

crankshaft.

Note:

Do not place the plastic clearance gauge on the oil hole of the main journal

Install the bearing bush on the engine base and install the engine base on the body.

Tighten the bolts with the specified torque in the order of the numeric marks on the

engine base.

Locking torque:

tightening

15 Nm

tightening

30 Nm

tightening

6 Nm

tightening

12 Nm

Remove the engine base and measure the width of each plastic clearance gauge after

being compressed. If the specified value is exceeded, replace the bearing bush.

Oil clearance: 0.012

～

0.044mm

Note:

Do not turn the crankshaft until the measurement is completed

Engine body and base

Check the engine body and base for cracking, damage and corrosion; If any, replace it.

Check the cooling water channel for dirt or blockage; If any, clean it.

Содержание F60 BEL-D

















































































































Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды

Parsun F60 BEL-D, Руководство по обслуживанию

Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды