Parsun F60 BEL-D Скачать руководство пользователя страница 34

Страница: 34 / 112

Spark Plug Ignition

Remove the spark plug cap from the spark plug.

1. Spark plug cap; 2. Spark plug

Connect the ignition detector to the spark plug cap.

Start the engine and observe the spark through the discharge window of the detector.

Warning:

Do not touch any joint of the detector lead.
Stay away from combustible gases or liquids to avoid accidents caused by spark ignition.

Spark Plug Cap

Unscrew spark plug cap. Check the spark plug cap for damage. Replace it if necessary.

Install spark plug cap.

Flywheel Maintenance

1. Remove the flywheel nut using the flywheel gripper; Remove the flywheel using the

flywheel puller.

Check whether the flywheel is damaged and whether the permanent magnet is firm.
Replace it if necessary.

Check the Ignition Coil

Remove the ignition coil and the spark plug cap.

Measure the resistance of the ignition coil. If the specified value is not met, replace it.

Primary resistance: 2.2±0.22Ω

Secondary resistance 9.84±0.98kΩ

Check the trigger coil

Trigger coil peak voltage
Use a digital multimeter and a peak voltage adapter to measure the coil output peak

voltage. If it is below the specified value, check the tri|gger coil resistance.

Digital multimeter Peak voltage adapter

Pulse coil peak voltage: ≥13 V@

1000 r/min (load)

Содержание F60 BEL-D

















































































































Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды

Parsun F60 BEL-D, Руководство по обслуживанию

Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды