Parsun F60 BEL-D Скачать руководство пользователя страница 111

Страница: 111 / 112

106

Common Faults and Solutions

Fault

Type

Cause

Solution

The engine
cannot start

No fuel in the fuel tank

Fill up the fuel tank with clean fresh fuel

Fuel is contaminated or obsolete

Fuel filter is blocked

Replace the fuel filter

Fuel pump failure

Repair or replace the fuel pump

Fuel tank cap vent screw not loosened

Loosen the vent screw

Spark plug is contaminated or the type
is incorrect

Check the spark plug. Clean the spark plug or replace with
the correct type of spark plug

Incorrect installation of the spark plug
cap

Check and reinstall the spark plug cap

Ignition wire failure

Check the wiring. Tighten the loose wire and replace
aged or broken wire.

Ignition parts Failure

Replace

The engine stop safety cable is not
connected to the emergency stop switch
assembly.

Connect the cable to the switch

Engine internal parts failure

Repair

Abnormal
engine idle or
stall

Spark plug is contaminated or the type
is incorrect

Clean the spark plug or replace with the correct type of
spark plug

Fuel system is clogged

Check the fuel pipe for extrusion, winding or blockage

Fuel is contaminated or obsolete

Fill up the fuel tank with clean fresh fuel

Fuel filter is blocked

Replace the fuel filter

Incorrect spark plug clearance

Adjust the clearance to the specified value

Ignition wire failure

Check the wiring. Tighten the loose wire and replace
aged or broken wire.

Incorrect oil grade

Change to the oil of the specified grade

Thermostat failure

Replace

Fuel pump failure

Replace

The vent screw for the fuel tank cap is
not loosened

Loosen the vent screw

Fuel joint is not connected correctly

Connect it correctly

Chock valve handle is pulled out

Return it to its original position

Outboard angle too high

Return it to its normal operating position

Engine
weakness

Propeller is broken

Repair or replace the propeller

Incorrect trim angle

Adjust the trim angle to an appropriate angle

Incorrect installation height of
outboard motor

Adjust it to the correct height

The bottom of the ship is polluted by
Lower casing organisms.

Clean the bottom of the ship

The gearbox is twined by aquatic
plants or foreign matters

Remove foreign matter and clean it

Содержание F60 BEL-D

















































































































Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды

Parsun F60 BEL-D, Руководство по обслуживанию

Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды