Parsun F60 BEL-D Скачать руководство пользователя страница 112

Страница: 112 / 112

107

Continued table (I)

Fault type

Cause

Solution

Engine
weakness

Spark plug is contaminated or the type is
incorrect

Clean the spark plug or replace with the correct type
of spark plug

Fuel system is clogged

Check the fuel pipe for extrusion, winding or blockage

Fuel filter is blocked

Replace the fuel filter

Fuel is contaminated or obsolete

Fill up the fuel tank with clean fresh fuel

Incorrect spark plug clearance

Adjust the clearance to the specified value

Ignition wire failure

Check the wiring. Tighten the loose wire and replace
aged or broken wire.

Ignition parts failure

Replace

The engine oil grade is incorrect or too
much oil is added.

Change to the oil of the specified grade or add it to the
appropriate position of the oil dipstick.

Thermostat failure

Replace

Fuel pump failure

Replace

Fuel joint is not connected correctly

Connect it correctly

Incorrect spark plug specification

Replace it with the correct model

Excessive
vibration
of
outboard
motor

Propeller is broken

Repair or replace the propeller

Propeller shaft is broken

Replace

The propeller is twined by aquatic plants or
foreign matters

Remove foreign matter and clean it

Mounting bolt of outboard motor is loose

Tighten the bolt

Steering shaft is loose

Tightening the spindle

Steering shaft is broken

Replace

Содержание F60 BEL-D

















































































































Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды

Parsun F60 BEL-D, Руководство по обслуживанию

Результаты поиска

Содержание F60 BEL-D

Отзывы:

Похожие инструкции для F60 BEL-D

Бренды по названию

Популярные бренды