Parkside ZKGS 2100, Инструкции по эксплуатации и безопасности

Страница: 16 / 24

between the blade (7) and the turntable
(16) equals 90°.
Retighten the counter nut (d) to secure this
setting.
Check the position of the pointer (21) on
the scale (20). If necessary, release the
pointer (21) with a crosstip screwdriver,
move to the 0° position of the scale (20)
and retighten.
7.4 Final adjustment of the stop for meter
cut 45° (Fig. 1, 7, 9 – 10)
An angular stop is not supplied.
Fasten the turntable (16) in 0° position.
Undo the securing screw (23) and tilt the
machine head (5) to the right to an angle of
45° using the handle (1).
Place the 45° stop angle (b) between the
blade (7) and the turntable (16).
Adjust the adjustment screw (30) until the
angle between the saw blade (7) and the
turntable (16) is 45°.
8. Operation
8.1 Crosscut 90° and turntable 0°-45°
(Fig 1–3, 12)
Important! The integral resetting springs will
automatically lift the machine head. Do not
simply let go of the handle (1), but allow the
machine head (5) to rise slowly, applying slight
counterpressure as it does so.
For cutting widths up to approx. 100 mm it is
possible to fix the saw’s drag function with the
locking screw for drag guide (24) in rear
position. If the cutting width exceeds 100 mm
you must ensure that the locking screw for
drag guide (24) is slackened and that the
machine head (5) can be moved.
Move the machine head (5) to its upper
position.
Push the machine head towards the rear
(5) with the handle (1) and, wherever
necessary, fasten it in this position
(according to cutting width).
Place the piece of wood to be cut at the
stop rail (19) and on the turntable (16).
Fasten the material with the clamping
device to the immobile sawing table (17) to
prevent movement during the cutting
process.
Push the release lever (3) to release the
machine head (5).
Push the ON-OFF switch (2) to switch on
the motor.
For fixed drag guidance (26), move the
machine head (5) with the handle (1)
evenly and with light pressure downwards,
until the saw blade (7) has cut through the
workpiece.
With the drag guide (26) not fixed in place:
Pull the machine head (5) all the way to the
front. Lower the handle (1) to the very
bottom by applying steady and light
downward pressure. Now push the
machine head (5) slowly and steadily to the
very back until the saw blade (7) has
completely cut through the workpiece.
Once the sawing process is over, let the
machine head (5) move back into the upper
resting position and let go of the ON/OFF
switch (2)
8.2 Crosscut 90° and turntable 0°-45°
(Fig 1-3, 13)
With the crosscut saw it is possible to make
crosscuts of 0° - 45° to the left and 0° - 45° to
the right up to the stop rails.
Release the turntable (16) by slackening
the locking grip (13).
Press the latched position lever (12). Turn
the turntable (16) and scale pointer (14) to
the desired angular setting on the scales
(15) and lock into place with the locking
grip (13). The saw has locking positions at
angles of - 45°, -30°, -22,5°, -15°, 0°, 15°,
22,5°, 30° and 45°, at which you can
engage latched position lever (12).
Cut as described under Section 8.1.
GB
16
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 16