65
DE/AT/CH
Schwingzahl einstellen
Wählen Sie mit dem
Geschwindigkeitsregler
[
4]
die Schwingzahl
aus (Abb. J).
Stufe 1:
Niedrige Schwingzahl
Stufe 6:
Hohe Schwingzahl
HINWEIS
u
Die erforderliche Schwingzahl ist vom
Werkstoff und den Arbeitsbedingungen
abhängig und kann durch praktischen
Versuch ermittelt werden.
u
Die Schwingzahl kann auch während des
Betriebs geändert werden.
Ein- und Ausschalten
m
VORSICHT! VERLETZUNGSRISIKO!
Tragen Sie stets Schutz hand schuhe,
wenn Sie mit dem Produkt hantieren
oder arbeiten.
m
VORSICHT! VERLETZUNGSRISIKO!
u
Halten Sie während der Arbeit das Produkt
stets mit beiden Händen fest (Abb. I).
m
VORSICHT! VERLETZUNGSRISIKO!
u
Halten Sie Ihre Hände vom Einsatz werk-
zeug fern, wenn das Produkt in Betrieb ist.
m
VORSICHT! GESUNDHEITSRISIKO!
u
Asbesthaltiges Material darf nicht
bearbeitet werden. Asbest gilt als
krebserregend.
(Abb. K)
Einschalten:
Schieben Sie den Ein-/
Ausschalter
[
10]
nach vorn (
ON
). Die LED-
Arbeitsleuchte
[
8]
wird zusammen mit dem
Produkt eingeschaltet.
Ausschalten:
Schieben Sie den Ein-/
Ausschalter
[
10]
nach hinten (
OFF
). Die
LED-Arbeitsleuchte
[
8]
wird automatisch
ausgeschaltet.
Probelauf
HINWEIS
u
Führen Sie vor dem ersten Arbeiten und
nach jedem Einsatzwerkzeugwechsel
einen Probelauf ohne Belastung durch.
Der Probelauf gewährleistet, dass das
Einsatzwerkzeug korrekt eingespannt ist
und sich während des Betriebs nicht lösen
kann.
Arbeitshinweise
Arbeitsprinzip:
Durch den oszillierenden Antrieb schwingt
das Einsatzwerkzeug 5000 bis 20000 Mal
pro Minute hin und her. Das ermöglicht
präzises Arbeiten auf engstem Raum.
Sägen/Trennen:
Verwenden Sie ausschließlich
unbeschädigte, einwandfreie Sägeblätter.
Verbogene, unscharfe oder anderweitig
beschädigte Sägeblätter können brechen.
Beachten Sie beim Sägen von
Leichtbaustoffen die gesetzlichen
Bestimmungen und Empfehlungen der
Materialhersteller.
Es dürfen nur weiche Werkstoffe
wie Weichholz, Gipskarton o. Ä. im
Tauchsägeverfahren bearbeitet werden!
Sandpapierschleifen:
L
Schleifpapier anbringen:
Drücken
Sie das Schleifpapier
[
21]
auf die
Sandpapierschleifplatte
[
20]
(Abb. L).
Содержание PAMFW 12 E4
