Service/Spare Parts Manual
Series V12
MSG30-5506-M1/UK
15
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
15
Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series V12
HY30-5506-M1/UK
Assembling, complete unit
48. Assemble the cylinder barrel. Make sure
that all rollers are in place.
49. Make sure the support pin is in correct
position by using a steel wire.
50. Assemble the gasket and lubricate it with
hydraulic oil.
51. Assemble the bearing housing. Carefully
knock it down with a plastic hammer. Secure
the housing by assembling one screw.
52. Assemble the gasket and lubricate it with
hydraulic oil.
53. Assemble the end cap assy. Mind your
fingers, don't squeeze them.
Refer to page 14 for end cap location.
15
Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series V12
HY30-5506-M1/UK
Assembling, complete unit
48. Assemble the cylinder barrel. Make sure
that all rollers are in place.
49. Make sure the support pin is in correct
position by using a steel wire.
50. Assemble the gasket and lubricate it with
hydraulic oil.
51. Assemble the bearing housing. Carefully
knock it down with a plastic hammer. Secure
the housing by assembling one screw.
52. Assemble the gasket and lubricate it with
hydraulic oil.
53. Assemble the end cap assy. Mind your
fingers, don't squeeze them.
Refer to page 14 for end cap location.
Assembling, complete unit
48. Assemble the cylinder barrel. Make sure that all rol-
lers are in place.
49. Make sure the support pin is in correct position by
using a steel wire.
50. Assemble the gasket and lubricate it with hydraulic
oil.
51. Assemble the bearing housing. Carefully knock it
down with a plastic hammer. Secure the housing by
assembling one screw.
15
Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series V12
HY30-5506-M1/UK
Assembling, complete unit
48. Assemble the cylinder barrel. Make sure
that all rollers are in place.
49. Make sure the support pin is in correct
position by using a steel wire.
50. Assemble the gasket and lubricate it with
hydraulic oil.
51. Assemble the bearing housing. Carefully
knock it down with a plastic hammer. Secure
the housing by assembling one screw.
52. Assemble the gasket and lubricate it with
hydraulic oil.
53. Assemble the end cap assy. Mind your
fingers, don't squeeze them.
Refer to page 14 for end cap location.
15
Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series V12
HY30-5506-M1/UK
Assembling, complete unit
48. Assemble the cylinder barrel. Make sure
that all rollers are in place.
49. Make sure the support pin is in correct
position by using a steel wire.
50. Assemble the gasket and lubricate it with
hydraulic oil.
51. Assemble the bearing housing. Carefully
knock it down with a plastic hammer. Secure
the housing by assembling one screw.
52. Assemble the gasket and lubricate it with
hydraulic oil.
53. Assemble the end cap assy. Mind your
fingers, don't squeeze them.
Refer to page 14 for end cap location.
52. Assemble the gasket and lubricate it with hydraulic
oil.
53. Assemble the end cap assy. Mind your fingers,
don’t squeeze them. Refer to page 17 for end cap
location.
15
Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series V12
HY30-5506-M1/UK
Assembling, complete unit
48. Assemble the cylinder barrel. Make sure
that all rollers are in place.
49. Make sure the support pin is in correct
position by using a steel wire.
50. Assemble the gasket and lubricate it with
hydraulic oil.
51. Assemble the bearing housing. Carefully
knock it down with a plastic hammer. Secure
the housing by assembling one screw.
52. Assemble the gasket and lubricate it with
hydraulic oil.
53. Assemble the end cap assy. Mind your
fingers, don't squeeze them.
Refer to page 14 for end cap location.
15
Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series V12
HY30-5506-M1/UK
Assembling, complete unit
48. Assemble the cylinder barrel. Make sure
that all rollers are in place.
49. Make sure the support pin is in correct
position by using a steel wire.
50. Assemble the gasket and lubricate it with
hydraulic oil.
51. Assemble the bearing housing. Carefully
knock it down with a plastic hammer. Secure
the housing by assembling one screw.
52. Assemble the gasket and lubricate it with
hydraulic oil.
53. Assemble the end cap assy. Mind your
fingers, don't squeeze them.
Refer to page 14 for end cap location.
Aassembling, complete unit
