background image

PSK Models

PSK201N5

PSK201N7

PSK221N5EXBS

PSK221N7EXBS

PSK231N5EXBS

PSK231N7EXBS

PSK203N5

PSK203N7

PSK223N5EXBS

PSK223N7EXBS

PSK233N5EXBS

PSK233N7EXBS

PSK204N9

PSK214N9EXBS

Inputs

NTC/PTC 
Temperature Sensor

1

1

1

2

2

2

2

2

Door Switch

1

1

1

1

Multipurpose

1

1

1

1

1

Relay Outputs

Compressor

16A

16A

30A

16A

8A

30A

16A

16A

Evaporator Fan

8A

5A

5A

8A

8A

Defrost Solenoid

8A

8A

8A

8A

8A

Multipurpose

1

8A

8A

Features

IP65 Rated Front Panel

3

3

3

3

3

3

3

3

Extractable Terminals

3

3

3

3

3

TTL Serial 
Communication Port

3

3

3

3

3

Built-In Alarm Buzzer

3

3

3

3

3

Energy Saving Mode

3

3

3

3

3

3

HACCP Data Logging

3

3

Real Time Clock (RTC)

3

Power

115 VAC, 50/60 Hz

N5

N5

N5

N5

N5

N5

230 VAC, 50/60 Hz

N7

N7

N7

N7

N7

N7

115-230 VAC, 50/60 Hz

N9

N9

1. See “Product Features” for details.

Form 100-359 / 12014

© 2014 Parker Hannifin Corporation

standard

Product Features

Temperature Probes

The PSK controllers are 
compatible with both NTC 
and PTC type temperature 
sensors. While the default 
is NTC, the PSK unit can 
be easily installed into an 
existing system using PTC 
sensors.

Configurable Input

The multipurpose input on 
select PSK models can be 
configured for an additional 
temperature probe (e.g.: 
condenser over-heat sensor), 
a door switch (a second door 
switch on the 204 and 214 
models), or as a digital input. 
The digital input can be used 
to synchronize defrosts, 
activate energy saving mode, 
activate an alarm, or to turn 
the controller off.

Extractable Terminals

The plug-in terminal block 
is available on select PSK 
models and allows for quick, 
easy installation.

Configurable 

Relay Output

The PSK204 and PSK214 
models offer an additional 
relay output, which is 
configurable for any of the 
following:
•  General purpose, 

auxiliary output

•  Cabinet light
•  2nd compressor
•  External alarm
•  Defrost synchronization
•  Anti-sweat heater
•  Door frame heater
•  Evaporator Valve

Technical Specifications

Connections

: Screw terminal block or extractable terminal block (power supply, 

inputs, outputs); 6-pin connector (serial communications port)

Sensor Probes:

 NTC or PTC (must be configured)

Sensor Range:

  -40 to 105°C (-40 to 220°F) for NTC;

 

-50 to 150°C (-50 to 300°F) for PTC

Operating Temperature:

 0 to 55°C (32 to 131°F)

Item

Part Number

NTC Temperature Probe with 5 ft. (1.5 m) cable

952899

NTC Temperature Probe with 10 ft. (3 m) cable

952898

PSK Programming Key

PSKey

PSKey Power Supply

PSPS01

TTL to RS485 Adaptor

PSIF20TSX

Accessories

Product Selection

Parker Hannifin Corporation

Sporlan Division

206 Lange Drive, Washington, MO 63090 USA 
phone 636 239 1111 
fax 636 239 9130 
www.sporlan.com

Содержание Sporlan PSK Series













































Отзывы: