Parker Sporlan PSK Series Скачать руководство пользователя страница 26

Page 2 

– Bulletin 100-50-6.4

2  USER INTERFACE

2.1  Introductory comments
The device has the following operational states:
•  “on” (power is connected and the controller is on: the regulators 

may be switched on)

•  “stand-by” (power is connected but software sets the controller to 

off: the regulators are switched off; the option of manually switch-
ing on/off the cabinet light or the auxiliary output depends on 
parameter u2).

The term “turning on” is understood to mean switching from the 
stand-by state to on; the term “turning off” is understood to mean 
switching from the on state to the stand-by state.
When the controller is turned on, it restores the state it was in when 
power was interrupted.

2.2  Manual switching on/off of the controller
•  make sure the keyboard is not locked and no procedure is running
•  press and hold    for 4 seconds.
It is also possible to turn the controller on/off using the multifunction 
input.

2.3  The display

If the controller is turned on, during normal operation the display 
will show the quantity you have set with parameter P5.
While in stand-by mode the display is turned off.

2.4  Showing the temperature read by the probes
•  make sure the keyboard is not locked and no procedure is running
•  press and hold 

 for 2 seconds: the display will show the first 

available label

•  press 

 or 

  to select “

Pb1” (cabinet probe), “Pb2” (evaporator 

probe), or “

Pb3” (auxiliary probe) 

•  press 
To quit the procedure:
•  press 

  or do not press any other buttons for 60 seconds

•  press 

 or 

 as long as the display shows the quantity you have 

set with parameter P5 or do not press any other buttons for 60 
seconds.

Alternatively:
•  press 
If there is no evaporator probe (parameter P3 = 0), label “

Pb2” will 

not be shown.
If the function of the fourth input is not for an auxiliary probe (pa-
rameter P4 = 0 or 3), then label “

Pb3” will not be shown.

2.5  Manually activating defrost
•  make sure the keyboard is not locked and no procedure is running
•  press and hold 

 for 4 seconds.

If the function of the evaporator probe is set for a defrost probe 
(parameter P3 = 1) and the evaporator temperature is above that 
established by parameter d2, then defrost will not be activated.

2.6  Manually turning on/off the cabinet light 

(only if parameter u1 is set to 0)

•  make sure no procedures are running
•  press 
It is also possible to turn the cabinet light on/off remotely using the 
microport and multifunction inputs; see also parameter u2.

2.7  Manually turning on the anti-sweat heater 

(only if parameter u1 is set to 1)

•  make sure the controller is turned on and no procedures are running
•  press 

 for 2 seconds: the anti-sweat heater will be turned on for 

the period of time established by parameter u6.

Manually turning off of the anti-sweat heater is not permitted.

2.8  Manually turning on/off the auxiliary output 

(only if parameter u1 is set to 2)

•  make sure the keyboard is not locked and no procedure is running
•  press 
It is also possible to turn the auxiliary output on/off using the multi-
function input.
The auxiliary output can be turned off manually by the same process 
in section 2.8, only if it was turned on manually (the same applies for 
remotely turning on the auxiliary output); see also parameter u2.

2.9  Locking/unlocking the keyboard
To lock the keyboard:
•  make sure no procedures are running
•  press and hold 

 and 

 for 2 seconds: the display will show 

Loc” for 1 second.

If the keyboard is locked, it will not be possible to:
•  manually turn the device on/off
•  show the temperature read by the cabinet probe, evaporator probe, 

or auxiliary probe (using the procedure indicated in paragraph 2.4)

•  manually activate defrost
•  manually turn the auxiliary output on/off
•  view information pertaining to the HACCP alarms
•  delete the HACCP alarm list
•  change the operational setpoint using the procedure indicated in 

paragraph 3.1

•  display the total hours of compressor operation
•  delete the total hours of compressor operation.
These operations will cause the label “

Loc” to be displayed for 1 

second.
To unlock the keyboard:
•  press and hold 

 and 

 for 2 seconds: the display will show 

UnL” for 1 second.

3 SETTINGS

3.1  Setting the working setpoint
•  make sure the keyboard is not locked and no procedure is running
•  press 

: LED   will flash

•  press 

 or 

 within 15 seconds; also see parameters r1, r2 and r3

•  press 

 or do not press any other button for 15 seconds.

You also can modify the working setpoint through parameter SP.

3.2  Setting the configuration parameters
To gain access to the procedure:
•  make sure no procedures are running
•  press and hold 

 and 

 for 4 seconds: the display will show “

PA

•  press 
•  press 

 or 

 within 15 seconds to set the display to “

-19

•  press 

 or do not press any other button for 15 seconds

Содержание Sporlan PSK Series













































Отзывы: