Introduction
Follow these instructions when installing, operating, or servicing
the product.
Application Limits
These products are intended for use in general-purpose compressed
air systems only.
Operating Pressure:
kPa
PSIG
bar
Maximum Inlet Pressure
1035
150
10.0
Minimum Inlet Pressure
210
30
2.0
Ambient Temperature Range:
4°C to 54°C (40°F to 130°F)
Voltage Range:
Rated V10%, -15%
Symbol
Installation
The Solenoid Quick Exhaust
valves should be installed with
reasonable accessibility for service. Keep pipe or tubing lengths to
a minimum with inside clean and free of dirt and chips. Pipe joint
compound should be used sparingly and applied only to the male
pipe – never into the female port. Do not use PTFE tape to seal
pipe joints – pieces have a tendency to break off and lodge inside
the unit, possibly causing malfunction. Care should be taken to
avoid undue strain on valve.
Air applied to the valve must be filtered with a 40 micron filter to
realize maximum component life.
!
WARNING
To avoid unpredictable system behavior that can cause personal injury
and property damage:
• Disconnect electrical supply (when necessary) before installation,
servicing, or conversion.
• Disconnect air supply and depressurize all air lines connected to
this product before installation, servicing, or conversion.
• Operate within the manufacturer’s specified pressure, temperature,
and other conditions listed in these instructions.
• Medium must be moisture-free if ambient temperature is below
freezing.
• Service according to procedures listed in these instructions.
• Installation, service, and conversion of these products must be
performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
• After installation, servicing, or conversion, air and electrical
supplies (when necessary) should be connected and the product
tested for proper function and leakage. If audible leakage is present,
or the product does not operate properly, do not put into use.
• Warnings and specifications on the product should not be covered
by paint, etc. If masking is not possible, contact your local
representative for replacement labels.
!
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF
THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR
RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND
PROPERTY DAMAGE.
This document and other infor mation from The Company, its
subsidiaries and authorized distributors provide product and/or system
options for further investigation by users having technical expertise. It
is important that you analyze all aspects of your application, including
consequences of any failure and review the information concerning
the product or systems in the current product catalog. Due to the
variety of operating conditions and applications for these products or
systems, the user, through its own analysis and testing, is solely
responsible for making the final selection of the products and systems
and assuring that all performance, safety and warning requirements
of the application are met.
The products described herein, including without limitation, product
features, specifications, designs, availability and pricing, are subject to
change by The Company and its subsidiaries at any time without notice.
EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR
INCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE
THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.
Life Expectancy
-
Normal multi-million cycle life expectancy of
these valves is based on the use of properly filtered and lubricated
air at room temperature. These valves are also designed to operate
under non-lubricated conditions and will yield millions of maintenance
free cycles.
Factory Pre-Lubrication
-
Valves are pre-lubricated at assembly
with a petroleum based grease which has a lithium content.
In-Service Lubrication
-
In-service lubrication is not required;
however, if lubrication is to be used, F442 oil is recommended. This
oil is specially formulated to provide peak performance and
maximum service life from all air operated equipment. Otherwise,
use an air line lubricant (compatible with Nitrile & Polyurethane
seals) which will readily atomize and be of the medium aniline type.
Aniline point range must be between 180° and 220°F.
Viscosity at 100°F: 140 - 170 SUS.
!
CAUTION: Do not use synthetic, reconstituted, or oils with
an alcohol content or detergent additive.
!
CAUTION:
Do not restrict the inlet of valves having an
internal pilot supply. Pressure supply piping must be the
same size as the inlet port or larger to insure that the pilot
valve receives sufficient pressure supply during high flow
conditions.
Accessories
Kit No.
Description
Metal Mufflers
ES50MB 1/2"
Exhaust Muffler - S75
ES75MB 3/4"
Exhaust Muffler - S105
Plastic Mufflers
M60-04 1/2"
Exhaust Muffler - S75
M60-06 3/4"
Exhaust Muffler - S105
Function
The Solenoid Quick Exhaust valve is a 3-Port normally closed
3-Way, 2-Position directional control valve, which supplies
downstream pressure when the solenoid is energized. Upon de-
energizing of the solenoid, the inlet air is blocked and the downstream
air is exhausted. The bottom (exhaust) port is tapped 1/2” NPTF on
the S75 and 3/4” NPTF on the S105 so that the exhaust may be
piped away of fitted with a muffler.
Pneumatic Division
Richland, Michigan 49083
269-629-5000
Installation & Service Instructions
IS-S75/S105
Solenoid Quick Dump Valve
1/4", 3/8" & 1/2" S75 &
3/8", 1/2" & 3/4" S105
ISSUED: February, 2005
Doc. #ISS75S105, ECN #050142, Rev. 1
