background image

 3

Parker Hannifin

Pump and Motor Division
Trollhättan, Sweden

Service Manual

Series F02

Bulletin HY30-5519-M1/UK

Design and function

F2 is a piston pump with spherical pistons (1) inclu-

ding piston rings (2). The pistons are working at the 

angle of 40° to the shaft (3). When the shaft rotates, 

the pistons move up and down in the cylinder barrel 

(4), forcing the oil to pass from the inlet port to the 

outlet in the end cap (5). A ring gear (6) connects the 

cylinder barrel to the drive shaft, causing these to 

rotate at the same speed.

A barrel support (7) with a spring presses the cylinder 

barrel against the end cap. An internal connection 

from the housing to the suction port eliminates a se

-

parate drain line to the tank. F2 is provided with shaft 

and connection flange that fits direct to PTO´s with ZF 

standard.

  

Specifications

Frame size

F2-42/42

F2-53/53

F2-55/28

F2-70/35

F2-70/70

Displacement

 (cm

3

/rev)

Port A

43

54

55

69

68

Port B

41

52

28

36

68

Max operating pressure

 (bar)

 intermittent 

400

400

400

400

350

 continuous 

350

350

350

350

300

Max shaft speed

 (rpm)

(unloaded pump; low pressure)

2550

2550

2550

2550

2550

Max selfpriming speed

 (rpm)

Ports A

1)2)  

and B

1)2)

 pressurised

1800

1800

1800

1800

1650

Port A

2)  

unloaded, pressure in port B

2100

2100

2100

2100

2100

Input power

 (kW)

max intermittent

3)

 

100

126

100

126

131

max continuous 

88

110

88

110

112

Weight

 (kg)

19

19

19

19

19

1)   

Valid with 2

1

/

2

" inlet (suction) line; 

    

with 2" inlet line: 53/53 and 70/35 max 1100 rpm

 

 

42/42 and 55/28 max 1400 rpm. (q≈120l/min)

2)   

Measured at 1.0 bar abs. inlet pressure. 

 

Please note:

 A lower inlet pressure affects pump performance.

3)   

Max 6 seconds in any one minute.

1

2

5

6

7

3

4

Содержание F2 Series













Отзывы: