Parker 650 Series Скачать руководство пользователя страница 16

Страница: 16 / 17

Easy Start Guide

13. How to reset the Inverter to Factory Defaults

Page 15

This guide has been produced by The Inverter Drive Supermarket Ltd.
All content, including but not limited to graphics, text and procedures copyright

The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

Parker SSD Drives 650 Series Inverter

13.1 Power-on with up and down keys pressed

With the power supply to the drive off, press and hold the
up and down arrow keys and switch the power supply on.

13.2 Release up and down keys when “data” is
displayed.

When the display flashes “data”, release the up and down
keys.
Press the “E” (Escape) key to continue.

13.3 Drive initialises

The display briefly shows “init” to indicate that the drive is
initialising.

13.4 Reset complete

Once the reset is completed the display shows the speed
reference screen (as shown in the illustration opposite)
and the drive is ready.

Note that the “hand” icon indicates that the drive is in
local mode (control via keypad only). See section 9 for
more information regarding Local and Remote control
modes.

Содержание 650 Series

















