Parker 404 Скачать руководство пользователя | Manualshive

Страница: 28 / 47

background image

404/406XR Series Product Manual

Chapter 5 - Component Mounting Procedures

28

Parker Hannifin Corporation

1140 Sandy Hill Road
Irwin, PA 15642

www.parkermotion.com



Locate correct parallel mounting hardware for

bottom

position ‘C’:

Item #

404XR

406XR

128
129

(2) Pulley

(2) Pulley

132

(1) Belt

(1) Belt

(1) Shroud

(1) Shroud

126

(1) Cover Plate

(1) Cover Plate

515

(4) M4 x 8 Button Head Screws

(4) M5 x 10 Socket Head Cap Screws

541

(4) M4 Ribbed Spring Washers

(4) M5 Spring Washers

540

(4) M5 x 18 Socket Head Cap Screws

(4) M6 x 16 Socket Head Cap Screws

539

(4) M3 x 8 Button Head Screws

(4) M4 x 10 Button Head Screws



Apply a few drops of Loctite #609 to screw shaft. Mount Pulley #1 to positioner drive screw shaft by slipping it
over the screw shaft and up against the bearing assembly locknut. Tighten clamp screw to 13 in-lbs. Place
Shroud over pulley and onto mounting surface. Measure the distance from open face of shroud to the face of
pulley flange. The pulley should be recessed some distance from the open face of the shroud. Using depth
micrometer record this number.



Mount parallel mounting shroud (less cover plate) to 404/406XR series linear positioner in desired orientation.
Apply a few drops of Loctite # 242 on the screw threads. For

side

positions ‘A’ and ‘B’ install and tighten (2)

socket head cap screws, Item # 540, through the deep counterbored holes and install and tighten (2) button
head screws, Item # 517, through the remaining holes. For

bottom

position ‘C’ install and tighten (4) socket

head cap screws, Item # 540, 517, through the deep counterbored holes.

Motor

Description

DIM "A"

DIM "B"

DIM "C"

DIM "D"

404XR

SM 16

34.5 [1.36]

4.5 [0.18] 45.0 [1.77] 45.0 [1.77]

NEMA 23
SM 23

35.5 [1.40]

5.5 [0.22] 58.0 [2.28] 58.0 [2.28]

406XR

NEMA 23
SM 23

57.5 [2.26]

5.5 [0.22] 70.0 [2.76] 65.0 [2.56]

NEMA 34
NEOMETRIC 34

62.0 [2.44] 10.0 [0.39] 83.0 [3.27] 83.0 [3.27]

APEX 602/604
NEOMETRIC 70

62.0 [2.44] 10.0 [0.39] 70.0 [2.76] 70.0 [2.76]

" 322MM" REF

66,0 REF.
[2,60]

110,0 REF.
[4,33]

122,5 REF.
[4,82]

SQUARE BOX
DENOTES 406XR

www.comoso.com

«
...
26
27
28
29
30
...
»

Содержание 404
















































Отзывы:

Нет отзывов

Похожие инструкции для 404

Бренд: +GF+ Страницы: 4

Бренд: KAUP Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды