background image

5

GENERAL INSTALLATION INSTRUCTIONS

Paraskim™ Venturi Skimmer (Gunite/Concrete) Installation (For skimmer dimensions, see page 19)
NOTICE: When the skimmer is formed into the concrete shell of the pool it MUST be surrounded 
by at least 4" of structural concrete in a monolithic pour, using a cold joint as shown in installation 
drawings

 

(Fig. 1).

CAUTION: Plastic solvent cements and primers can be flammable, poisonous, or both. Closely follow 
solvent cement manufacturer’s instructions when using solvent cement.
CAUTION: In residential installations where equalizers are not required and where the main drain lines 
do not connect to the skimmer equalizer port, low water levels in the pool, spa, or hot tub or clogged 
skimmer baskets may damage the pump due to loss of prime (if skimmer pulls air) or cavitation (if 
skimmer clogs). Air pulled in by skimmer(s) can be trapped in filter tanks, which may be a safety hazard. 
If skimmer regularly vortexes or sucks air, raise water level or contact your pool service representative 
for advice.
1. For optimum skimmer functionality, the skimmer should be placed relative to the prevailing wind and 

water flow direction. 

2. Assemble piping and pipe fittings to skimmer. All piping must conform to current local and state 

plumbing and sanitary codes.

3. Long pipe runs and elbows restrict water flow. For best efficiency, use the fewest possible fitting 

and 2" pipe for 2" skimmers). Using sweep 90˚ fittings or two 45˚ fittings in place of a single 90 is 
more efficient.

4. For pressure testing seal off any used ports.

Over tightening the threaded plugs may result in failure of the plug or the 
skimmer body and will not be covered under the terms of the Limited Warranty.
DO NOT use tapered metal plugs as this will void manufacturer’s warranty. 

DO NOT use “Rector Seal” or other thread paste intended for gas pipe installations as this will attack the 
plastic and cause failure of the skimmer body and will not be covered under the terms of the Limited Warranty.

NOTICE

5. Support skimmer securely in position. Unused ports may be used to install a standpipe for the 

skimmer to rest on or skimmer may be tied to steel cage. The deck ring collar has a friction fit that 
allows 3½" of vertical adjustment. Additional 
collars may be stacked upon each other to 
accommodate desk height as needed.

6. Ensure piping is adequately supported on 

undisturbed earth. If additional backfilled and 
tamping is necessary, do not stress pipe or 
skimmer port by lifting or moving pipe after 
skimmer port connections have been made.

7. Structural gunite/concrete should be applied 

in a monolithic pour, in conjunction with a cold 
joint as shown in Fig. 1.

8. Optional Overflow Line – Using a 1½" hole saw 

drill out the overflow port at side top of skimmer 
to install overflow line. Plumb with a 1½" or 2" (2" 
pipe requires coupler) properly sloped line so that 
water flows away from the pool to desired point of 
discharge.

4"

COLD JOINT

TILE

TILE

18"

11"

REBAR CAGE

OVERFLOW

PORT

Fig. 1
Steel detail

Содержание Paraskim





















Отзывы: