Paragon Sentry 3.0 страница 39 Скачать руководство пользователя

Страница: 39 / 40

Keep the kiln lid or door closed when the kiln is not in use.

Sentry Ramp-Hold Shorthand Instructions

After you press the keys in the left column, the message to the right will appear. (See also page 15.)

KEYS TO PRESS

DISPLAY

COMMENTS

PROGRAM AND FIRE THE KILN.

Apply power to kiln

IDLE

Press Enter if IDLE does not appear.

USER

Enter program number.

A number from 1 to 35

Program number appears.35

ENTER

RA 1

Enter rate of segment 1.

Rate

0200

Rate appears.

ENTER

°F 1

Enter temperature of segment 1.

Temperature

2000

Temperature appears.

ENTER

HD 1

Next, enter hold time.

Hold time (0 if none)

00.00

Hold time appears.

Repeat for other segments. Enter rate of 0 for 1st segment not needed.

ENTER

IDLE

The kiln is ready to fire.

ENTER

-ON-

Kiln is now firing.

SELECT AND FIRE A STORED USER PROGRAM.

Apply power to kiln

IDLE

Press Enter if IDLE does not appear.

USER

Select a program number.

A number from 1 to 35

Displays the number you selected.

ENTER

RA1

STOP, STOP

IDLE

Selected program is ready to fire.

ENTER

-ON-

Kiln is now firing. (Use Program Review by pressing 6.)

AppendixF:

Содержание Sentry 3.0









































Результаты поиска

Содержание Sentry 3.0

Отзывы:

Похожие инструкции для Sentry 3.0

Бренды по названию

Популярные бренды

Paragon Sentry 3.0, Инструкция по эксплуатации

Результаты поиска

Содержание Sentry 3.0

Отзывы:

Похожие инструкции для Sentry 3.0

Бренды по названию

Популярные бренды