Paragon P7 Скачать руководство пользователя страница 6

LT6757 ( Iss 1 06/14 )

 

 

 

P7  Users Instructions

 

SECTION ONE Operating Appliance Continued 

 

LOW  BATTERY  INDICATION  (HAND 

SET) 

If while pressing any of the buttons on 

the 

remote hand set the low battery indicator 

lamp 

either stops flashing or appreciably 

slows 

then the battery should be changed. 

 
TO REPLACE BATTERY IN HAND SET 

(9V 

SIZE 2X1.5V AAA) 

Remove  the  cover  from  the  rear  of  the 

handset 

and  fit  replacement  battery.  Take  care 

not 

to 

stain the battery connections. 

 

LOW 

BATTERY 

INDICATION 

(APPLIANCE) 

If  you  hear  a  repeated  ‘bleep’  sound 

come 

from the appliance this indicates the appliance battery pack is low and should be changed as soon as 
possible. The appliance will continue to work normally for a short period but if the warning is ignored 
you may experience difficulty lighting the appliance or the appliance may automatically switch off for 
no apparent reason.  

NOTE:

 The appliance cannot be used when the battery is completely flat. 

 

TO REPLACE APPLIANCE BATTERIES (6 High Power Alkaline AA 1.5V) 
(Rechargeable batteries can be used providing they are a nickel metal hydride type 1.5V AA 
with a minimum capacity of 2200mAh). 
(A long life lithium battery is available as an optional extra call the number shown on the last 
page of these instructions for further information). 

 

a.  Lift off the outer trim or Inlet Cover 
b.  The battery power pack holder is located on the right 

hand  side  on  the  base  of  the  Firebox  or  within  the 
fireplace  frame  assembly.   

WARNING,  batteries 

will overheat if fitted incorrectly, when fitting the 
batteries  ensure  that  they  are  fitted  as  per  the 
marking  on  the  rear  of  the  holder  (i.e.  minus  of 
battery  against  spring). 

If  rechargeable  batteries 

are used they MUST be a Nickel Metal Hydride type with a minimum capacity of 2200mAh.  

c.  If  the  appliance  is  fitted  with  the  special  lithium  battery  (optional)  disconnect  the  wires  at  the 

battery connector and replace ensuring the connection is made correctly. 

d. 

Important:

  Place  the  battery  pack  or  holder  inside  the  insulation  blanket  and  ensure  that  it  is 

placed to the left hand side of the appliance as shown and refit fret and ash pan cover. (Illustration 
shows lithium battery without insulation sleeve.) 

e. Once the new batteries are loaded the fire will continue to bleep until re-set. This can be done by   
pressing the “off “ button on the handset followed by the normal ignition sequence as above. If the fire 
continues to bleep this may indicate a loose connection or badly loaded batteries. 
 

 

 
 
 
 
 
 

 

Содержание P7





























Отзывы: