Paragon Fires Focus RS Скачать руководство пользователя страница 3

LT4548 (10:09/10) 

3

 

PARAGON FOCUS RS 

 Users Instructions

 

 

SECTION ONE 

Important Information 

 

Consumer Protection Information 

As  manufacturers  and  suppliers  of  heating  products,  we  take  every  care,  as  far  as  is  reasonably 
practicable,  that  these  products  are  so  designed  and  constructed  as  to  meet  the  general  safety 
requirement  when  properly  used  and  installed.  To  this  end,  our  products  are  thoroughly  tested  and 
examined before despatch. 
 

IMPORTANT  NOTICE:

  Any  alteration  that  is  not  approved  by  the  appliance  manufacturer  could 

invalidate  the  approval  of  the  appliance,  operation  of  the  warranty  and  could  affect  your  statutory 
rights.

 

 

Health and Safety Notice 

Important 

This  appliance  could  contain  some  of  the  materials,  indicated  below,  that  could  be  interpreted  as 
being  injurious  to  health  and  safety.  It  is  the  users  /  installers  responsibility  to  ensure  that  the 
necessary  personal  protective  clothing  is  worn  when  handling  these  materials,  see  below  for 
information. 

Artificial Fuels, Mineral Wool, Insulation Material, Refractory/Ceramic Fibres, Glass Yarn - 

may 

be harmful if inhaled, may be irritating to skin, eyes, nose and throat.  

When handling

 

avoid inhaling and contact with skin or eyes. Use disposable gloves, facemasks 

and  eye  protection.  After  handling  wash  hands  and  other  exposed  parts.  If  a  vacuum  is  used  for 
cleaning  the  coals  or  cleaning  after  servicing  /  installation  it  is  recommended  that  it  be  of  the  type 
fitted with a HEPA filter. 

Disposal  of  refractory/ceramic  materials

To  keep  dust  to  a  minimum  these  materials 

should be securely wrapped in polythene and be clearly labelled ‘RCF waste’. These materials are 
not classified as ‘hazardous waste’ and should be disposed of at a site licensed for the disposal of 
industrial waste.

 

 

The PARAGON FOCUS RS is an inset room sealed decorative fuel-effect gas appliance. 

 

The PARAGON FOCUS RS is available in 

Natural Gas (G20 @ 20 mbar) or LPG ( G31 @ 37 

mbar Only).

 The marking (

G20

 for natural gas) or (G31 for Propane Gas Only) 

on the packaging 

and  the  data  badge  specify  the  gas  for  which  the  appliance  has  been  factory  set. 

Note:  These 

appliances should only be used on the appropriate gas specified. They are not suitable for 
conversion from one gas to the other.

 

 

The PARAGON FOCUS RS 

must not

 be installed into a natural draught flue or chimney. 

 

Failure to install appliance correctly could lead to prosecution. 
In  GB  (Great  Britain),  the  appliance  must  be  installed  and  serviced  by  a  competent  person  i.e. 
CORGI-registered,  in  accordance  with  the  GAS  SAFETY  (INSTALLATION  AND  USE) 
REGULATIONS,  The  Building  Regulations  (or  The  Building  Regulations  (Scotland)  or  The 
Building Regulations (Northern Ireland)) and The Current I.E.E. Wiring Regulations, if appropriate.  
In IE (Ireland), the appliance must be installed and serviced by a competent person and installed 
in  accordance  with  the  current  edition  of  I.S.813  Domestic  Gas  Installation,  the  current  Building 
Regulations and the current ETCI rules for electrical installation, if appropriate.   

  The PARAGON FOCUS RS does not require a chimney, but 

must be

 installed against an outside 

wall. 

 

It is important that the flue terminal is regularly checked and kept clear at all times. 

 

If  the  terminal  is  accessible  to  people  (i.e.  less  than  2m  above  a  walkway,  balcony  etc.)  the 
terminal guard must be fitted to prevent access to the flue outlet, which becomes hot when the fire 
is in use.

 

 

All combustible material must be removed from behind the fire and fire trim. 

Содержание Focus RS





























Отзывы: