Paradyne ACCULINK 3160 страница 24 Скачать руководство пользователя

Страница: 24 / 31

Table 9. General Management Configuration Options (1 of 2)

Option

Factory 1

Factory 2

Comments/Description

SNMP Mgt:

Disab

Specifies whether the DSU/CSU
responds to SNMP session

SNMP Mgt:

Enab

responds to SNMP session
requests.

NMS Valid:

Enab

Specifies whether the DSU/CSU
validates the IP address of an

NMS Valid:

Disab

validates the IP address of an
SNMP manager attempting
access.

Num Sec Mgrs:

The number of SNMP managers

Num Sec Mgrs:

2–10

The number of SNMP managers
allowed to access the DSU/CSU.

NMS

n IP Adr:

Edit

Allows you to define or clear the
allowable IP address of an SNMP

NMS

n IP Adr:

Clear

allowable IP address of an SNMP
manager.

NMS

n Acs:

Read

The type of access allowed for an
SNMP manager using community

NMS

n Acs:

R/W

SNMP manager using community
name 1.

System Name:

Edit

The SNMP system name for this

System Name:

Clear

The SNMP system name for this
device.

System Location:

Edit

The SNMP system location for this

System Location:

Clear

The SNMP system location for this
device.

System Contact:

Edit

The SNMP system contact name

System Contact:

Clear

The SNMP system contact name
for this device.

CommunityName1:

Edit

A community name that is allowed
access to this device Defaults to

CommunityName1:

Clear

access to this device. Defaults to
public.

Access 1:

Read

The type of access allowed for

Access 1:

R/W

The type of access allowed for
community name 1.

CommunityName2:

Edit

A community name that is allowed

CommunityName2:

Clear

A community name that is allowed
access to this device.

Access 2:

Read

The type of access allowed for

Access 2:

R/W

The type of access allowed for
community name 2.

IP Adr:

Edit

The IP address needed to access

IP Adr:

Clear

The IP address needed to access
the device.

NetMask:

Edit

The Subnet Mask needed to

NetMask:

Clear

The Subnet Mask needed to
access the device.

Com IP Adr:

Edit

The IP address for the COM port

Com IP Adr:

Clear

The IP address for the COM port
when configured for SNMP.

Содержание ACCULINK 3160
































Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды

Paradyne ACCULINK 3160, Быстрая справка

Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды