background image

5910-A2-GZ40-00

May 2005

7

Technical Specifications

 

 Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product 

and included in this manual.

2. Use a Listed/Certified minimum 24 AWG (0.205 mm

2

) wire for connection to 

the interface connectors.

3. This equipment is to be connected behind the telephone line primary 

protector.

4. Do not attempt to install or service this product yourself, as opening or 

removing covers may expose you to dangerous high-voltage points or other 
risks. Refer all installation and servicing to qualified service personnel.

5. When installed in the final configuration, the product must comply with the 

applicable Safety Standards and regulatory requirements of the country in 
which it is installed. If necessary, consult with the appropriate regulatory 
agencies and inspection authorities to ensure compliance.

6. In addition, since the equipment is to be used with telecommunications 

circuits, take the following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically 

designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the 

telephone line has been disconnected at the network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical 

storm. There may be a remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

Specification

Criteria

Available Modules

„

5910-B1-000 – 24-Port 900 Ohm Module, No DC 
Blocking

„

5910-B1-004 – 24-Port 600 Ohm Module, No Signature 
Circuitry, No DC Blocking 

Capacity

192 Subscriber Loops

Compliance

T1.413, ITU-T G992.1, G992.3, G992.5 CSA/UL, 
FCC part 68, CS03, NEBS

Height x Width x Depth

3.5

 x 16.9

 x 10.6

 (89 mm x 430 mm x 270 mm) 

Impedance

600–900 ohms

Physical Environment

Operating temperature

Shock and vibration

–40

°

 C to 70

°

 C (–40

°

 F to 158

°

 F)

Withstands normal shipping and handling

Weight

16.1 lb (7.3 kg)

!

Содержание 5910









Отзывы: