Paradyne 3350 Скачать руководство пользователя

Страница: 79 / 122

Configuration Options

C-13

3350-A2-GB20-10

June 1996

Table C-7

(1 of 2)

SNMP Trap Configuration Options

Num Trap Mgrs: 1
Next 1 2 3 4 5 6 Prev

Number of Trap Managers. Specifies the number of SNMP trap managers that are to receive traps for this unit.

NOTE: You must configure an IP address for each trap manager that is to receive trap messages.

Trap

n IP Adr:

Next Edit Clear Prev

Trap

n IP Address. Specifies the IP address for each trap manager. This configuration option is repeated for all trap

managers supported by the unit.

Edit – Allows you to edit or display the IP address for Trap Manager

Clear – Allows you to clear the IP address for Trap Manager

n. The IP address is set to 000.000.000.000.

Trap

n Dst: None

Next None Com Aux FDL Prev

Trap Manager

n Destination. Specifies the network destination for Trap Manager n. This configuration option is displayed

for the number of trap managers (

n) specified by the Number of Trap Managers configuration option.

None – No Trap Manage

n network destination. Traps are discarded.

Com – The Trap Manager

n network destination is the communication port. This selection only appears if the Com Use

configuration option is set to SNMP or Daisy.

Aux – The Trap Manager

n network destination is the auxiliary port. This selection only appears if the Aux Use

configuration option is set to SNMP or Daisy.

FDL – The Trap Manager

n network destination is the FDL management link. This selection only appears if the FDL

management link is enabled for SNMP.

NOTE: If the chosen destination link is disabled or down, the traps are discarded. Return to this menu and choose

another destination.

Gen Trap: Both
Next Disab Warm Auth Both Prev

General Trap Types. Specifies the general trap types to enable. For more information, refer to the

SNMP Traps section in

Chapter 4,

Maintenance.

Disab – Disables the sending of trap messages for warmStart and authenticationFailure events.

Warm – Sends trap messages for warmStart events to the currently configured trap manager(s).

Auth – Sends trap messages for authenticationFailure events to the currently configured trap manager(s).

Both – Sends trap messages for warmStart and authenticationFailure events to the currently configured trap manager(s).

NOTE: This configuration option is not available if the SNMP Trap configuration option (in the

Alarm Configuration

Options section) is disabled.

Содержание 3350



























































































































Результаты поиска

Содержание 3350

Отзывы:

Похожие инструкции для 3350

Бренды по названию

Популярные бренды

Paradyne 3350, Руководство пользователя

Результаты поиска

Содержание 3350

Отзывы:

Похожие инструкции для 3350

Бренды по названию

Популярные бренды