PaperFolder PH-Knife-14 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 19

background image

Page 9

PaperFolder.com

OUTPUT WHEELS

Adjust the output wheels for the type of fold. In for shorter; out for longer. Start longer and shorten if
needed. You do not want the paper to back up into the machine.

INSTALLING THE FOLD PLATES

If you are installing the fold plates for the first time, please see the section above on setting the fold.

Two of the fold plates, 2 and 4, may come installed in the machine. Install any remaining fold plates
in this order: 4, 2, 3, 1. The trays have numbers on them. They fit on the 2 posts with the
corresponding numbers, e.g., Plate 4 goes on the 2 posts marked 4.

«
...
7
8
9
10
11
...
»

Содержание PH-Knife-14




















Отзывы:

Нет отзывов

Похожие инструкции для PH-Knife-14

Бренд: Truvox Страницы: 12

Бренд: Briteq Страницы: 8

Бренд: Smoke Factory Страницы: 16

Бренд: ROOTS Страницы: 164

Бренд: Janome Страницы: 30

Бренд: COMAC Страницы: 29

Бренд: Clarke Страницы: 6

Бренд: IPS Страницы: 6

Бренд: JUKI Страницы: 9

Бренд: Necta Страницы: 45

Convertamatic 200E 56324004

Бренд: Nilfisk-Advance Страницы: 17

Бренд: Nilfisk-Advance Страницы: 80

Carpetriever 28

Бренд: Nilfisk-Advance Страницы: 84

Бренд: Nilfisk-Advance Страницы: 81

Бренд: Nilfisk-Advance Страницы: 38

Бренд: Singer Страницы: 39

Бренд: Yamaha Страницы: 30

Бренд: Atlanta Attachment Company Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды