PaperFolder PH-Knife-14 Скачать руководство пользователя страница 15

Страница: 15 / 19

Page 15

PaperFolder.com

TROUBLESHOOTING IN OPERATION

Symptom

Cause

Solution

Paper is not folded at
proper folding
position

The paper folding plate is

not installed properly.

Install the paper folding
plate properly.

tatic electricity has

occurred in the paper.

Spray a commercially-

available

air duster on the rubber roll

Paper is double

-fed frequently

The paper separator is dirty Clean it with alcohol

The sheets of paper are
sticking

to each other

Fan the paper well

Paper jams

frequently

The rubber roll is dirty

Clean it with alcohol

Paper shreds are stuck

inside the paper
conveyance passage

Check inside the machine

and

remove any paper shreds

The stacker roller position is

not correct

Adjust the position of the

stacker rollers

The paper is curled

Straighten the paper curl

Static electricity has

occurred in the paper

Spray a commercially-

available air duster on the
rubber roller

Paper slips in the

vertical direction

After a paper type was

changed, a folding
position has not been

Check that the rough

adjustment knob position is
correct

Paper slips in the

Horizontal direction

The paper is stacked

unevenly

Stack the paper neatly on

the paper feed table

There is space between
the paper and side guide

Set the side guides so that
they push against the paper

lightly

The rubber roll is deformed Call your dealer

Содержание PH-Knife-14




















Результаты поиска

Содержание PH-Knife-14

Отзывы:

Похожие инструкции для PH-Knife-14

Бренды по названию

Популярные бренды

PaperFolder PH-Knife-14, Руководство пользователя

Результаты поиска

Содержание PH-Knife-14

Отзывы:

Похожие инструкции для PH-Knife-14

Бренды по названию

Популярные бренды