PaperFolder PH-Knife-14 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 19

background image

Page 5

PaperFolder.com

IF YOU ARE INSTALLING THE PH14 TO OPERATE BY ITSELF

Slide the output tray into machine just below the rubber rollers. The 2 slots on the end fit on a bar.
Lower it with the slots fitting on the bottom on the outer bar. Make sure the gears are aligned on the
right side.

Install the output wheels by placing the side of the T-shaped mount with the spring in the hole closest
to the rollers on the left side of the machine. Note that it has to go under the cross bar. Press it in so
that you have clearance to put the right side in the hole on the right side. Attach the output wheels

as shown along with the output tray extension.

«
...
3
4
5
6
7
...
»

Содержание PH-Knife-14




















Отзывы:

Нет отзывов

Похожие инструкции для PH-Knife-14

Бренд: Olivetti Страницы: 72

Бренд: Pfaff Страницы: 19

Бренд: Foamit Страницы: 10

Бренд: Mannsberger Страницы: 22

Бренд: Briteq Страницы: 8

CARRUSEL FIESTA

Бренд: falgas Страницы: 26

Бренд: Home Accents Holiday Страницы: 2

Бренд: Singer Страницы: 27

Бренд: IPC Soteco Страницы: 40

Бренд: Panasonic Страницы: 100

Бренд: GBC Страницы: 25

Бренд: Baby Lock Страницы: 128

KXTG9345 - HANDSET

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 4

KXTG2258S - 2.4 GHZ DIGITAL CDL

Бренд: Panasonic Страницы: 3

KXTG9348 - EXPANDABLE DIGITAL CORDLESS ANS SYS

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды