Panduit smartzone G5 Скачать руководство пользователя страница 91

Страница: 91 / 98

SMARTZONE G5 USER MANUAL

147-154

The sensor (1-8) temperature/humidity is ABOVE critical
threshold value

155-162

The sensor (1-8) temperature/humidity is BELOW critical
threshold value

163-170

The sensor (1-8) contact state is in alarm.

183

User authentication failed.

186

Power or relay communication lost to main board

193

Firmware update failed.

Trap codes assigned for warning alarms:

Trap Class Trap

Code

Trap Description

Warning

200

The PDU unit active power is ABOVE warning threshold
value.

201

The PDU unit active power is BELOW warning threshold
value.

202-204

The phase (1-3) voltage is ABOVE warning threshold value.

205-207

The phase (1-3) voltage is BELOW warning threshold value.

208-210

The phase (1-3) current is ABOVE warning threshold value.

211-213

The phase 1 current is BELOW warning threshold value.

214-225

The circuit breaker (1-12) current is ABOVE warning
threshold value.

226-237

The circuit breaker (1-12) current is BELOW warning
threshold value.

238-249

The circuit breaker (1-12) is in OFF state.

Содержание smartzone G5



































































































Результаты поиска

Содержание smartzone G5

Отзывы:

Бренды по названию

Популярные бренды

Panduit smartzone G5, Руководство пользователя

Результаты поиска

Содержание smartzone G5

Отзывы:

Бренды по названию

Популярные бренды