37
36
U S E R A N D I N S TA L L AT I O N MA N UA L
PA N D O R A M I N I M OTO
Level №4 – Reset to the factory settings
The procedure recovers the factory settings of the system without deleting previously registered
devices (tags, mobile device, relays, etc.) that is stored in the non-volatile memory.
Enter the programming level №4:
• Press and hold the VALET button for more than 4 seconds. Release the button after a sound of the
Siren. The system will confirm the resetting to the factory settings with a long red flash of the LED
indicator. After that, the system will reset the settings to default and return to the programming
level №0.
Level №10 – Manage Bluetooth devices / Firmware Update
!
a
ll
addiTiONal
dEvicEs
iNcludEd
iN
ThE
sysTEm
sET
arE
pairEd
wiTh
ThE
sysTEm
. T
hE
maximum
NumbEr
Of
pairEd
b
luETOOTh
dEvicEs
musT
NOT
ExcEEd
14.
a
ll
fuNcTiONs
Of
This
lEvEl
arE
availablE
iN
ThE
p
aNdOra
s
pEcialisT
app
whEN
usiNg
a
b
luETOOTh
cONNEcTiON
.
f
Or
ThE
maNagEmENT
Of
ThE
addiTiONal
dEvicEs
gO
TO
«a
dvaNcEd
mOuNTiNg
» -> «p
airiNg
/
uNpairiNg
dEvicEs
».
f
Or
ThE
firmwarE
updaTE
Of
ThE
addiTiONal
dEvicEs
gO
TO
«a
dvaNcEd
mOuNTiNg
» -> «s
ysTEm
dEvicEs
».
f
Or
a
dETailEd
dEscripTiON
Of
pairiNg
prOcEdurE
fOr
spEcific
dEvicE
chEck
iT
’
s
maNual
ON
www
.
paNdOraiNfO
.
cOm
.
This level is used to pair/remove/update additional devices of the system. Each device is paired at
a sublevel. To pair devices of the same type, a sublevel is divided into cells. To enter a sublevel or a
cell of sublevel make a pause for more than 1 second, then press (
P
) the VALET button the number of
times equals to the desired sublevel or cell number: «Level №10» (1sec) «Sublevel 1…10» (1sec) «Cell
of sublevel 1…4».
PAIRING/DELETING AN ADDITIONAL DEVICE
Each sublevel or cell displays it’s current state by a color of the LED: green light means the system is
ready for pairing, red light means a device has been already paired and it is required to delete it for
pairing a new device. To delete a device, press and hold the VALET button for 3 seconds (4 orange
flashes of the LED, or 3 sound signals of the Siren). The system will be in pairing mode for 1 minute.
After a minute or immediately after pairing a device, the system will automatically enter the
programming level №0.
PAIRING RADIO TAGS BT760/BT770/BT780
• Enter the programing level №10.1.1…3.
• If the LED is green, the system is ready for pairing.
• Press and hold button on a tag until the 6 flashes of the tag status indicator, release the button ;
• The system will confirm pairing with a sound signal from the Siren and the LED will light red.
• The system will enter the programming level №0.
PAIRING PANDORA BAND
• Enter the programing level №10.2.1…3.
• If the LED is green, the system is ready for pairing.
• Press and hold button on the Band for 6 seconds;
• The system will confirm pairing with a sound signal from the Siren and the LED will light red.
• The system will enter the programming level №0.
PAIRING DOOR SENSOR DMS-100 BT
• Enter the programing level №10.3.1…4.
• If the LED is green, the system is ready for pairing.
• Open the plastic case of the sensor carefully and insert a battery inside.
• The system will confirm pairing with a sound signal from the Siren and the LED will light red.
• The system will enter the programming level №0.
PAIRING A SIREN PS-332 BT
• Enter the programming level «Pairing an additional device RHM-03BT/PS-331BT/PS-332BT» (level
№10.6);
• System is ready for pairing, the LED lights green;
• Put a magnet on the selected zone and connect the power supply, the siren will be paired with the
system;
• The system will confirm pairing with a sound signal from the Siren and the LED will light red.
• The system will enter the programming level №0.
UPDATING FIRMWARE OF AN ADDITIONAL DEVICE
• To update firmware of an additional device, enter the «Level №10» «Sublevel» or «Cell» corresponding
to an additional device. The LED will light red after entering. Press and hold the VALET button for 5
seconds until 6 orange flashes of LED indicator or 5 sound signals of the Siren. Open the Pandora
Specialist or Pandora BT app, go to «Search device» screen and select the device and then select one
of the update option:
• INTERNET – It allows you to upload firmware from a server.
• FILE MANAGER – This function is available only for Android devices. It allows you to upload firmware
from the phone storage.
