![background image](http://html.mh-extra.com/html/panasonic/wx-ct420/wx-ct420_operating-instructions-manual_262558017.webp)
17
w
Auto-Talk-Lock setup
For a Belt Pack where Auto-Talk-Lock is set up, it has a
function to select “TALK” automatically when the vehicle
detector has become active, and you can talk with the
customer at the menu board. One unit of this product or the
All-In-One Headset can be set to Auto-Talk-Lock setup per
lane.
p
Complete ID Registration, to do this setting.
p
You can set only the unit with its DIP switch No.1 in
the ON position.
(Refer to p. 20 “DIP switch setup”.)
Press the [POWER] button to turn on the
power.
p
When the power is turned on, the voice messages
“Hello”, “Headset xx” (xx: ID number registered in the
Center Module) and “Lane x” (x: Connected Lane
number) are heard from the speaker of the headset.
Press the [T1] button* while the power
indicator turns green and red alternately for 3
seconds.
p
Auto-Talk-Lock registration is performed to Lane A.
When registration is complete, the voice message
“Auto Talk ON” is heard from the speaker of the
headset, and the power indicator stops turning
alternately.
p
When the [T1] button of this product is not pressed
within 3 seconds after the power is turned on, the
voice message “Auto-Talk-Lock OFF” is heard from
the speaker of the headset, and the unit starts as
usual.
* Use the [T2] button to register Auto-Talk-Lock for
Lane B.
p
If there is a problem registering Auto-Talk-Lock,
an error beep and the voice message “Failed” are
heard from the speaker of the headset, and the
power indicator blinks red to alert the user the
abnormal state. If that happens, turn off the Belt
Pack and retry from step
.
p
If the power of the Belt Pack is turned off, all the
setting conditions for Auto-Talk-Lock will be canceled.
This setting should be carried out without fail when
the power supply is started up.
p
A Belt Pack in which the Auto-Talk-Lock function
has been enabled operates at the Talk-Lock setting
regardless of the DIP switch No.2 setting.
Note
w
ID registration
Before using this product, the unit ID must be registered in
the Center Module. After the ID is registered in the Center
Module, wireless communication between this product and
the Center Module is enabled.
Set the Center Module to “ID Registration”
mode.
(Refer to the operating instructions of the Center
Module.)
Hold down the [POWER] button for 2 seconds
or more to turn off the Belt Pack.
Press the [POWER] button for 1 second or
more while holding down the [T1] and [T2]
buttons to turn on the power.
p
The Belt Pack enters the ID Registration setting
mode. You will hear “Registration Mode” and the
power indicator will blink orange.
Press the [T1] button.
p
You can hear “Connecting Center Module A” and the
lane Indicator will blink orange.
p
When the Center Module is WX-CC412, ID
registration for Lane B is automatically started, the
voice message “Connecting Center Module B” is
heard from the speaker of the headset, and the lane
indicator blinks green.
p
When the ID Registration succeeds, you will hear
“Registration complete”, “Headset xx” (xx: ID number
registered in the Center Module), and the power
indicator stops blinking and stays on.
p
If ID registration fails, an error beep and the voice
message “Failed” are heard from the speaker of
the headset, and the power indicator blinks red to
indicate an abnormal state. If that happens, retry
from step 2.
When the ID registration is complete, cancel
“ID Registration” of the Center Module.
p
When this is done, “ID Registration” of this product is
cancelled and the power indicator turns green.
p
During ID registration, the other Belt Packs (or Order
Takers) or All-In-One Headsets cannot be used to talk
or page.
Note
English