Panasonic WH-UD16HE8 Скачать руководство пользователя | Manualshive

Страница: 26 / 44

background image

■

Outputs

Mixing valve

AC230V N=Neutral Open,

Close=mixture direction
Operating time: 30s~120s

Pool pump

AC230V

Solar pump

AC230V

Zone pump

AC230V

■

Thermistor inputs

Zone room sensor

PAW-A2W-TSRT

Buffer tank sensor

PAW-A2W-TSBU

Pool water sensor

PAW-A2W-TSHC

Zone water sensor

PAW-A2W-TSHC

Solar sensor

PAW-A2W-TSSO

Recommended External Device

Specification



This section explains about the external devices

(optional) recommended by Panasonic. Please
always ensure to use the correct external device
during system installation.



For optional sensor.

1. Buffer tank sensor: PAW-A2W-TSBU

Use for measurement of the buffer tank
temperature.
Insert the sensor into the sensor pocket and paste
it on the buffer tank surface.

40

black

brown

blue

Dimensions (mm)

Ø6

2. Zone water sensor: PAW-A2W- TSHC

Use to detect the water temperature of the control
zone.
Mount it on the water piping by using the stainless
steel metal strap and contact paste (both are
included).

93

70

35

Dimensions (mm)

3. Outdoor sensor: PAW-A2W-TSOD

If the installation location of the outdoor unit is
exposed to direct sunlight, the outdoor air
temperature sensor will be unable to measure the
actual outdoor ambient temperature correctly.
In this case, optional outdoor temperature sensor
can be fixed at a suitable location to more
accurately measure ambient temperature.

70

93

46

Dimensions (mm)

4. Room sensor: PAW-A2W- TSRT

Install the room temperature sensor to the room
which requires room temperature control.

Dimensions (mm)

86

86

60

30

5. Solar sensor: PAW-A2W-TSSO

Use for measurement of the solar panel
temperature.
Insert the sensor into the sensor pocket and paste
it on the solar panel surface.

40

black

brown

blue

Dimensions (mm)

Ø6

6. Please refer to the table below for sensor

characteristic of the sensors mentioned above.

Temperature

(°C)

Resistance

(kΩ)

Temperature

(°C)

Resistance

(kΩ)

30

5.326

150

0.147

25

6.523

140

0.186

20

8.044

130

0.236

15

9.980

120

0.302

10

12.443

110

0.390

5

15.604

100

0.511

0

19.70

90

0.686

-5

25.05

80

0.932

-10

32.10

70

1.279

-15

41.45

65

1.504

-20

53.92

60

1.777

-25

70.53

55

2.106

-30

93.05

50

2.508

-35

124.24

45

3.003

-40

167.82

40

3.615

35

4.375

«
...
24
25
26
27
28
...
»

Содержание WH-UD16HE8













































Отзывы:

Нет отзывов

Похожие инструкции для WH-UD16HE8

Бренд: wattio Страницы: 20

Бренд: C&K systems Страницы: 2

Бренд: Daikin Страницы: 56

Бренд: Danfoss Страницы: 36

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: Salda Страницы: 16

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: L-Acoustics Страницы: 20

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: ACS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды