Panasonic WH-UD16HE8 Скачать руководство пользователя

Страница: 21 / 44

11.1.6.4 Mounting The Remote

Controller

For exposed type

Preparation:

Make 2 holes for screws using a driver.

Cut here with
a nipper and
remove the burr
with a ﬁle.

Mount the top case.

•

Align the claws of the top
case and then align the claws
of the bottom case.

Hole for screw

Screw
(ﬁeld supply)

Claw (2 places)

Pass through

the hole

Bottom case

(Back side)

Top case
(Back side)

Remote controller terminal board

Remove the coating. Approx. 6 mm

Remove the sheath. Approx. 180 mm.
Make sure the wiring connection is in the
correct direction.

Clamper

(ﬁeld supply)

Claw (2 places)

Wall to which
the remote
controller is
ﬁxed

Mount the bottom case to

the wall.

Connect the remote control

wiring

•

Arrange the wires along the groove
of the case.

For embedded type

Preparation:

Make 2 holes for screws using a driver.

Avoid the wire
being caught.

Mount the top case.

•

Align the claws of the top
case and then align the claws
of the bottom case.

Hole for
screw

Screw
(ﬁeld supply)

Claw (2 places)

Bottom case

(Back side)

Top case
(Back side)

Remote controller
terminal board

Remove the coating.

Approx. 6 mm

Make sure the wiring
connection is in the correct
direction.

Claw (2 places)

Mount the bottom case

to the wall.

•

Pass the wire through the hole
in the centre of the bottom case.

Connect the remote

control wiring

11.1.6.5 Replace The Remote Controller

Cover



Replace the existing Remote controller cover with

Remote controller cover

to close the hole left

after remove the Remote controller.

1. Release the Remote controller cover’s hooks from

behind the front plate.

Front plate

Hook (6 places)

Existing Remote

controller cover

2. Press from front to fix the Remote controller cover

on the front plate.

Front plate

Hook (6 places)

Remote

controller
cover 6

11.1.7 Charging The Water



Make sure all the piping installations are properly

done before carry out below steps.

1. Turn the plug on the Air Purge Valve

outlet

anticlockwise by one complete turn from fully
closed position.

Air purge valve

Plug (turn
anticlockwise by
one complete turn)

Содержание WH-UD16HE8













































Результаты поиска

Содержание WH-UD16HE8

Отзывы:

Похожие инструкции для WH-UD16HE8

Бренды по названию

Популярные бренды

Panasonic WH-UD16HE8, Руководство по обслуживанию

Результаты поиска

Содержание WH-UD16HE8

Отзывы:

Похожие инструкции для WH-UD16HE8

Бренды по названию

Популярные бренды