Panasonic WH-SHF09D3E8 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 120

background image

64

14. Servicing

Mode

14.1 How to Take Out Front Plate

Please follow the steps below for take out front plate. Before removing the front plate of indoor unit, always

switch off all power supply (i.e. indoor unit power supply, heater power supply and tank unit power supply).

1 Remove the 2 mounting screws which located at bottom of the front plate and 1 mounting screw at the front

of the plate.

2 Gently pull the lower section of the front plate towards you to remove the front plate from left and right hooks.
3 Hold the left edge and right edge of front plate to lift up front plate from hooks.

14.2 How to Take Out Side Cabinet

Please follow the steps below to remove the side
cabinet. Before removing the front plate of indoor
unit always switch off all power supply (i.e. indoor
power supply, heater power supply and tank unit
power supply).
1 Perform the steps in HOW TO TAKE OUT

FRONT PLATE.

2 Remove all the 13 mounting screws on the left,

right and top of the side cabinet.

3 Gently remove the side cabinet by holding

both of the handles.

14.3 Test

Run

1 Fill up the boiler tank with water. For details refer to boiler tanks installation instruction and operation

instruction.

2 Set ON to the indoor unit and RCCB/ELCB. Then, for control panel’s operation please refers to air-to-water

heatpump’s operation instruction.

3 For normal operation, pressure gauge reading should be in between 0.05 MPa and 0.3 MPa.

If necessary, adjust the water pump speed accordingly to obtain normal water pressure operating range. If
adjust water pump speed cannot solve the problem, contact your local authorized dealer.

4 After test run, please clean the external filter. Reinstall it after finish cleaning.

14.4 Proper Pump Down Procedure

Strictly follow the steps below for proper pump down procedure. Explosion may occur if the steps are not

followed as per sequence.
1 Press the “SERVICE” switch on control panel to enter SERVICE mode. Operate the system in Sr :

01 mode for pump down operation.

2 After 10~15 minutes, (after 1 or 2 minutes in case very low ambient temperatures (< 10°C)), fully close

2 way valve.

3  After 3 minutes, fully close 3 way valve.
4  Press the “OFF/ON” switch on control panel to stop pump down operation.
5  Remove the refrigerant piping.

«
...
62
63
64
65
66
...
»

Содержание WH-SHF09D3E8

























































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SHF09D3E8

Бренд: Zibro Страницы: 34

Бренд: Jata Страницы: 32

Бренд: Jata Страницы: 28

Бренд: Jata Страницы: 28

Бренд: Davey Страницы: 4

Бренд: T.I.P. Страницы: 84

Бренд: KISANKRAFT Страницы: 44

Бренд: Parkside Страницы: 220

ESSENSSE NEO VCES3 AC Series

Бренд: 2VV Страницы: 20

MagicComfort MSH 300

Бренд: Waeco Страницы: 192

Бренд: Dyna-Glo Страницы: 41

Бренд: U.S. Products Страницы: 8

Бренд: salmson Страницы: 24

Бренд: Bryant Страницы: 12

Бренд: Malmbergs Страницы: 12

Бренд: HOMCOM Страницы: 8

Бренд: SKF Страницы: 32

Бренд: Scarlett Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды