Panasonic WH-SHF09D3E8 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 120

background image

50

12.1.5 Setting Water Outlet Temperature for Heat Mode

The set temperature define the parameters for the outdoor ambient temperature dependent operation of the unit.

Where by the internal water setting temperature is determined automatically depending on the outdoor
temperature. The colder outdoor temperatures will result in warmer water and vice versa. The user has the
possibility to shift up or down the target water temperature by control panel setting.

Change in setting water outlet temperature is updated every 30 minutes.

12.1.5.1 Heating

Mode

Operation Time Chart

Operation of heat pump provide heating capacity to room side by hot water through heating panel, floor or fan

coil.

1 3 ways valve control:

o

3 ways valve switch and fix to heating side.

2  Heat pump operate follow normal heating operation.
3  Backup heater operate follow normal operation.
4  Solar 3 way valve operates follow solar operation specification.
5  2 way valve opens.

12.1.6 Water Temperature Thermo Shift Setting

Switchs are ignored during “PUMPDW” = ON.

Switchs are ignored during “STATUS” = ON.

“

▲

”, “

▼

”, “SELECT” switch are ignored if “SETTING” = OFF.

“CANCEL” switch is ignored if “SETTING” = OFF & “STATUS” = OFF.

If “SET” Switch pressed for less than 5secs, immediately enter water temperature shift setting mode.

Once enter this setting mode, “SETTING” display is ON.

This setting mode is used to easily shift the target water outlet temperature.

«
...
48
49
50
51
52
...
»

Содержание WH-SHF09D3E8

























































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SHF09D3E8

Бренд: Radialight Страницы: 20

Бренд: Daikin Страницы: 52

Бренд: Daikin Страницы: 147

Бренд: Daikin Страницы: 175

Бренд: KDK Страницы: 40

iSOLAR PDP Series

Бренд: ICON Страницы: 24

ZHHS-01-10K-R290-V5-M

Бренд: JBG HT Страницы: 32

Бренд: Raymarine Страницы: 24

SunCentric Series

Бренд: Dankoff Solar Страницы: 11

Бренд: UNITED Страницы: 4

Бренд: Haverland Страницы: 64

Vectissimo CO180

Бренд: Rowenta Страницы: 10

Бренд: N'oveen Страницы: 36

Бренд: EINHELL Страницы: 44

Бренд: Gardenline Страницы: 28

ULTRASlimline 10222

Бренд: Seville Classics Страницы: 6

Бренд: BN Thermic Страницы: 4

Бренд: VOLTOMAT HEATING Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды