background image

7

1-1.  Tools Required for Installation (not supplied)

 1.  Flathead screwdriver
 2.  Phillips head screwdriver
 3.  Knife or wire stripper
 4.  Tape measure
 5.  Level gauge

 6.  Sabre saw or keyhole saw
 7.  Hacksaw
 8.  Core bits

 9.  Hammer
 10.  Drill

 11.  Tube cutter
 12.  Tube flaring tool
 13.  Torque wrench
 14.  Adjustable wrench
 15.  Reamer (for deburring)

1-2.  Accessories Supplied

See Table 1.

1-3.  Type of Copper Tube and Insulation Material

If you wish to purchase these materials separately from a local 
source, you will need:

1.  Deoxidized annealed copper tube for refrigerant tubing.

2.  Foamed polyethylene insulation for copper tubes as 

required to precise length of tubing. Wall thickness of the 
insulation should be not less than 5/16" (7.94mm).

3.  Use insulated copper wire for field wiring. Wire size varies 

with the total length of wiring.  
See the section 

“4. ELECTRICAL WIRING”

 for details.

CAUTION

CAUTION

Check local electrical codes and 
regulations before obtaining 
wire. Also, check any specified 
instructions or limitations.

1-4.  Additional Materials Required for Installation

1.  Refrigeration (armored) tape 

2.  Insulated staples or clamps for connecting wire 

 

(See your local codes.) 

3.  Putty 

4.  Refrigeration tubing lubricant 

5.  Clamps or saddles to secure refrigerant tubing 

6.  Scale for weighing 

1.  GENERAL

This booklet briefly outlines where and how to install the air conditioning system. Please read over the entire set of instructions for 
the outdoor unit and make sure all accessory parts listed are with the system before beginning.

Table 1 Outdoor Unit

Part name

Figure

Q’ty

U-72MF2U9 

U-72MF2U94   

(6 ton)

U-96MF2U9 

U-96MF2U94 

(8 ton)

U-120MF2U9 

U-120MF2U94

(10 ton)

U-144MF2U9 

U-144MF2U94

(12 ton)

Connection 

tubing

Outer 

 

diameter 
ø1-1/8"(ø28.58)

Inner 

 

diameter 

ø

1"(

ø

25.4)

0

0

1

1

Outer 

 

diameter 
ø7/8"(ø22.22)

Inner 

 

diameter 

ø

3/4"(

ø

19.05)

0

0

1

1

Outer 

 

diameter 
ø3/4"(ø19.05)

Outer 

 

diameter 

ø

5/8"(

ø

15.88)

0

1

0

0

Operating 
Instructions

paper

1

1

1

1

Installation 
Instructions

paper

1

1

1

1

01_302412_Eng.indd   7

2018/7/4   13:30:26

Содержание U-72MF2U94

































































Отзывы: