Panasonic U-72MF2U94 Скачать руководство пользователя

Страница: 60 / 64

Wired remote

control display

Detected contents

<<F01>>

Indoor thermistor is either open or damaged.

E1 thermistor on liquid side of indoor heat exchanger has failure. (E1)

<<F02>>

Indoor unit set as single split. (E2)

<<F03>>

E3 thermistor on gas side of indoor heat exchanger has failure. (E3)

<<F10>>

TA thermistor for intake air temperature (room temperature) of the indoor

unit has failure. (TA)

<<F11>>

BL thermistor for supply air temperature of the indoor unit has failure.
(BL)

F04

Outdoor thermistor is either open or damaged.

DISCH1 thermistor at the discharge of 1st compressor reading is
abnormal.

F05

DISCH2 thermistor at the discharge of 2nd compressor reading is
abnormal.

F06

EXG1 thermistor at the gas side of 1st heat exchanger of the outdoor
unit has failure. (EXG1)

F07

EXL1 thermistor at the liquid side of 1st heat exchanger of the outdoor

unit has failure. (EXL1)

F08

TO thermistor for outdoor ambient air temperature has failure. (TO)

F12

SCT thermistor at the suction refrigerant of compressors has failure.
(SCT)

F14

SCG thermistor at the outlet of subcooling heat exchanger in outdoor

unit has failure. (SCG)

F16

High pressure sensor of the outdoor unit has failure. (HPS)

F17

Low pressure sensor of the outdoor unit has failure. (LPS)

F23

EXG2 thermistor at the gas side of 2nd heat exchanger of the outdoor
unit has failure. (EXG2)

F24

EXL2 thermistor at the liquid side of 2nd heat exchanger of the outdoor

unit has failure. (EXL2)

<<P01>>

Protective device in indoor unit is activated.

Indoor fan motor activated thermal protector.

<<P09>>

Connection to the panel of indoor unit is not good.

<<P10>>

Float switch of drain pan safety is activated.

<<P12>>

Indoor fan inverter protection control is activated.

P14

Input detected at EXCT terminal on indoor PCB for refrigerant detector.

P03

Protective device in outdoor unit is activated.

1st compressor discharge temperature too high.

P04

Protection device activated. High pressure switch (63PH, 63PH1 or

63PH2) or compressor thermal protector (49C1 / 49C2).

P05

Missing phase in power input is detected at HIC for 1st compressor.

P15

Missing phase in power input is detected at HIC for 2nd compressor.

P16

Overcurrent of 1st compressor on the secondary side of inverter circuit,
or inverter failed to syncronize with rotation.

P17

2nd compressor discharge temperature too high.

P19

Inverter for 2nd compressor failed to start or failed to syncronize with

rotation.

P22

Fan motor or inverter drive of outdoor unit has failure.

P26

Overcurrent of 2nd compressor on the secondary side of inverter circuit,
or inverter failed to syncronize with rotation.

P29

Inverter for 1st compressor failed to start or failed to syncronize with

rotation.

<P31>

Indoor unit communication error of group control

wiring.

Other indoor unit in group control has an alarm.

F29

EEPROM on indoor unit PCB failure

F31

EEPROM on outdoor unit PCB failure

H01

Protective device for compressor No. 1 is

activated.

Overcurrent in 1st compressor.

H03

Current sensor for the 1st compressor is disconnected or shorted.

H05

DISCH1 thermistor at the discharge of 1st compressor is disconnected,
shorted or misplaced. (DISCH1)

H11

Protective device for compressor No. 2 is

activated.

Overcurrent in 2nd compressor.

H13

Current sensor for the 2nd compressor is disconnected or shorted.

H15

DISCH2 thermistor at the discharge of 2nd compressor is disconnected,
shorted or misplaced. (DISCH2)

H06

Low pressure is too low.

H08

Oil sensor fault. (Disconnection, etc.)

OIL1 thermistor for the oil of 1st compressor has failure. (OIL1)

H27

OIL2 thermistor for the oil of 2nd compressor has failure. (OIL2)

01_302412_Eng.indd 60

2018/7/4 13:31:05

Содержание U-72MF2U94

































































Результаты поиска

Содержание U-72MF2U94

Отзывы:

Похожие инструкции для U-72MF2U94

Бренды по названию

Популярные бренды

Panasonic U-72MF2U94, Руководство по установке

Результаты поиска

Содержание U-72MF2U94

Отзывы:

Похожие инструкции для U-72MF2U94

Бренды по названию

Популярные бренды