English
- 19 -
Level
and
Signal Quality
of the selected channel
will be shown. Press
OK
to start scan on the
selected RF channel. The found channels will be
stored in the channel list. You can press the
Back/
Return
button to cancel the scan. Then press the
Back/Return
button again or highlight
Finish
and
press
OK
to exit.
Manual Service Update:
Start a service update
manually. You can press
OK
or the
Back/Return
button to cancel the scan. Then press
OK
or the
Back/Return
button again to exit.
LCN:
Set your preference for LCN. LCN is the Logical
Channel Number system that organises available
broadcasts in accordance with a recognisable
channel number sequence (if available).
Channel Scan Type:
Set your scan type preference.
Channel Store Type:
Set your store type prefe-
rence.
Favourite Network Select:
Select your favourite
network. This menu option will be active, if more
than one network is available.
Cable
Channel Scan:
Start a scan for digital cable
channels. If available, operator options will be
listed. Select the desired one and press
OK
.
Scan
Mode
,
Frequency
and
Network ID
options may be
available. The options may vary depending on the
operator and the
Scan Mode
selections. Set the
Scan Mode
as
Full
if you don’t know how to set up
other options. Highlight
Scan
and press
OK
or the
Right directional button to start the scan. You can
press the
Back/Return
button to cancel the scan.
The channels that have already been found will be
stored in the channel list.
Single RF Scan:
Enter the
Frequency
value.
Signal Level
and
Signal Quality
of the selected
Frequency
will be shown. Highlight the
Scan
option and press
OK
or the Right directional button
to start scan. The found channels will be stored in
the channel list.
LCN:
Set your preference for LCN. LCN is the Logical
Channel Number system that organises available
broadcasts in accordance with a recognisable
channel number sequence (if available).
Channel Scan Type:
Set your scan type preference.
Channel Store Type:
Set your store type prefe-
rence.
Favourite Network Select:
Select your favourite
network. This menu option will be active, if more
than one network is available. This option may not
be available depending on the selected country
during the initial setup process.
Satellite
Channel Installation Mode:
Set this option as
Preferred Satellite
or
General Satellite
. The
channel list will also change depending on the
selected option here. In order to watch the channels
on the satellite you want, this option should be
selected accordingly. Set to
Preferred Satellite
to
watch operator channels, if you have performed
an operator installation. Set to
General Satellite
to watch other satellite channels, if you have
performed a normal installation.
Satellite Re-scan:
Start a satellite scan beginning
with the antenna selection screen. When this
scanning option is preferred, some scanning
configurations will not be available and thus the
preferences you made during the initial setup
process may not be changed.
For the
General Satellite
channel installation mode
the
SatcoDX Scan
option may also be available
here. For standard installation select
Normal
scan
. For SatcoDX installation select
SatcoDX
Scan
and copy the relevant sdx file into the root
directory of an USB storage device and connect it
to your TV. Highlight this option and press
OK
or the
Right directional button. The
Download SatcoDX
option will be highlighted, press
OK
or the Right
directional button to continue. Select the sdx file
from the connected USB storage device and press
OK
. Satellite selection screen will be displayed. The
status of the first satellite option will appear as
On
.
Highlight that satellite option and press
OK
. Set
the parameters corresponding to your system and
correct satellite and press
the
Back/Return
button
to return to the satellite selection screen.
Highlight
Next
and press
OK
to proceed with the SatcoDX
channel list installation. If the selected satellite is not
correct for SatcoDX installation, a warning dialogue
will be displayed on the screen. The satellite/s that
can be selected will be listed. Press
OK
to close the
dialogue and press
OK
or the
Back/Return
button
to return to satellite selection screen. Then set the
satellite accordingly.
Satellite Add:
Add satellite/s on which you want
to perform a channel scan. This menu option will
be active, if
Channel Installation Mode
is set to
General Satellite
.
Satellite Update:
Search for any updates by
repeating the previous scan with the same settings.
You will also be able to configure these settings
before the scan. Depending on the
Channel
Installation
Mode
setting, this option may not be
available or named differently depending on the
available services. Highlight the satellite and press
OK
to configure detailed satellite parameters.
Then press
the
Back/Return
button to return to
the satellite selection screen.
Highlight
Next
and
press
OK
to proceed.
