manualshive.com logo in svg

Panasonic TH-42LF60W, Руководство по эксплуатации, Страница: 7 / 68

Поделиться
Скачать
Panasonic TH-42LF60W Скачать руководство пользователя страница 7

7

Accessories

Accessories Supplied

Check that you have the Accessories and items shown 

Operating instruction 
book

CD-ROM  
(Operating 
instruction)

Remote control 
transmitter
N2QAYB000691

Batteries for the remote 
control transmitter
(R6 (UM3) Size × 2)

AC cord

Clamper × 3

 

 

 

Remote Control Batteries

Requires two R6 batteries.

1.  Pull and hold the hook, then open 

the battery cover.

2.  Insert batteries - note correct 

polarity (+ and -).

3.  Replace the cover.

+

-

+

-

“R6 (UM3)” size

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

   

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.

Observe the following precautions:

1.  Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2.  Do not combine a used battery with a new one.
3.  ZZ%€  ‚&€' ‚*K
4.  Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5.  Battery replacement is necessary when the remote control acts sporadically or stops operating the Display.
6.  Do not burn or breakup batteries. 

| @  :'K

Содержание TH-42LF60W





































































Отзывы:

Нет отзывов