40
RQT9252
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart
do not solve the problem, consult your dealer for instructions.
The following do not indicate a problem with this unit:
≥
Regular disc rotating sounds.
≥
Image disturbance during search.
To reset this unit
Page
Power
Operation
Displays
To restore the unit if it freezes
due to one of the safety
devices being activated
≥
Press and hold [
Í
/I] on the main unit for 10 seconds. (The settings remain unchanged.)
—
To return all settings other than
some settings to the factory
preset
≥
Select “Yes” in “Default Settings” in the Setup menu.
This returns all values in the Setup menu and the on-screen menu, except for “Remote
Control”, “On-screen Language”, “DVD-Video Ratings”, “BD-Video Ratings” and “Speaker” to
the default settings.
34
To return to the factory preset
≥
Reset the unit as follows:
1
Press [
Í
/I] on the unit to turn off the unit.
2
Press and hold [
9
/
5
], [
∫
] (Stop) and [
<
OPEN/CLOSE] on the unit at the same time
for more than 5 seconds until “PLEASE WAIT” is displayed on the unit.
3
The power is turned off automatically.
—
No power.
≥
Insert the AC mains lead securely into a known active household mains socket.
9
The unit switches to standby
mode.
≥
When the time set for the sleep timer has passed, the unit will be turned off.
≥
One of the unit’s safety devices is activated. Press [
Í
/I] on the main unit to turn the unit on.
18
—
The remote control doesn’t
work properly.
≥
The remote control and main unit are using different codes. Change
the code on the remote control.
Press and hold [OK] and the indicated number button at the same time
for more than 5 seconds.
≥
The batteries are depleted. Replace them with new ones.
≥
You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
≥
Coloured glass may obstruct the signal reception/transmission.
≥
Do not place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥
It may be necessary to set the code on the remote control again after changing the batteries.
43
10
10
—
—
43
The unit is on but cannot be
operated.
≥
Confirm the correct source is selected.
≥
Some operations may be prohibited by the disc.
≥
The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.
≥
One of the unit’s safety devices may have been activated. Reset the unit as follows:
1
Press [
Í
/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [
Í
/I] on the main unit for about 10
seconds. Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.
2
Press [
Í
/I] on the main unit to switch it on. If the unit still cannot be operated, consult the
dealer.
≥
Condensation has formed: Wait 1 to 2 hours for it to evaporate.
12
—
39
—
—
Play fails to start even when
[
1
PLAY] is pressed.
Play starts but then stops
immediately.
≥
Insert the disc correctly with the label facing up.
≥
The disc is dirty.
≥
You tried to play a blank disc or unplayable disc on this unit.
≥
The producers of the disc can control how discs are played. So you may not always be able
to control play as described in these operating instructions. Read the disc’s instructions
carefully.
≥
[DivX[
If playing DivX VOD content, refer to the homepage where you purchased it.
16
15
14, 15
—
15
Cannot eject disc.
≥
The unit may have a problem. While the unit is off, press and hold [
:
/
6
] and
[
<
OPEN/CLOSE] on the main unit at the same time for about 5 seconds. Remove the disc
and consult the dealer.
—
Startup is slow.
When the unit is turned on,
audio and video output takes a
long time.
It takes time before play starts.
≥
Startup takes time in the following situations.
– Immediately after a power failure or the AC mains lead is connected.
– When the unit is connected with an HDMI cable.
≥
[DivX[
This is normal on DivX video.
—
—
Cannot set “On” in “BD-Video
24p Output”.
≥
Only when the unit is connected to the HDMI terminal of a TV supporting 24p you can select
“On”.
36
“TV Power” function does not
work.
≥
This function works only when the unit is connected to a Panasonic TV (VIERA) that supports
HDAVI Control 2 or HDAVI Control 3.
≥
If “TV Power” is not shown even when the unit is connected with an HDMI cable, check the
connections and return to the factory preset. (Please refer to “To return to the factory preset”
in the troubleshooting guide.)
—
above
The display is dim.
≥
Change “FL Display” in the Setup menu.
35
The elapsed time displayed is
actually less than the playtime.
≥
The displayed play time is converted from the number of frames at 29.97 frames (equal to
0.999 seconds) to one second. There will be a slight difference between the time displayed
and the actual elapsed time (e.g., actual one-hour elapsed time may display as
approximately 59 minutes 56 seconds).
—
D
R
SCBT105GN-RQT9252-L.book Page 40 Monday, May 19, 2008 8:40 AM
