Panasonic S*C09*3E8 Series, Руководство по установке

Страница: 17 / 440

17
ENGLISH
Optional cables:
•
External control cable
•
Tank sensor cable
•
Outdoor air sensor cable
•
Tank OLP cable
•
Remote controller cable
•
Room sensor zone 1 cable
•
Room sensor zone 2 cable
•
Buffer tank sensor cable
•
Pool sensor cable
•
Water sensor zone 1 cable
•
Water sensor zone 2 cable
•
Demand signal cable
•
Solar sensor cable
•
SG signal cable
•
Heat/Cool switch cable
•
External Compressor switch cable
Optional cables:
•
3-way valve cable
•
2-way valve cable
•
Booster heater cable
•
Extra pump cable
•
Boiler contact cable
•
Power Supply 1 cord
•
Power Supply 2 cord
•
Indoor Unit/Outdoor
Unit Connecting cable
Optional cables:
•
Pump zone 1 cable
•
Pump zone 2 cable
•
Solar pump cable
•
Pool pump cable
•
Room thermostat zone 1 cable
•
Room thermostat zone 2 cable
•
Mixing valve zone 1 cable
•
Mixing valve zone 2 cable
from optional
PCB
from optional PCB
Terminal screw on PCB Maximum tightening torque cN•m {kgf•cm}
M3 50 {5.1}
M4 120 {12.24}
Connecting Cables Length
When connecting cables between Indoor Unit and external devices,
the length of the said cables must not exceed the maximum length
as shown in the table.
External device Maximum cables length (m)
Two-way valve 50
Three-way valve 50
Mixing valve 50
Room thermostat 50
Booster heater 50
Extra pump 50
Solar pump 50
Pool pump 50
Pump 50
Boiler contact 50
External control 50
Tank sensor 30
Room sensor 30
Outdoor air sensor 30
Tank OLP 30
Buffer tank sensor 30
Pool water sensor 30
Solar sensor 30
Water sensor 30
Demand signal 50
SG signal 50
Heat/Cool switch 50
External compressor switch 50
Connection of the main PCB
OLP for booster
heater
Zone 1 room sensor
Outdoor air sensor
Tank sensor
External control
Remote controller
Boiler contact
Extra pump
Booster heater
H C N L C O N C O N
Optional
Thermostat 1 3-way
valve
2-way
valve
 
Signal inputs
Optional Thermostat
L N =AC230V, Heat, Cool=Thermostat heat, Cool
terminal

It does not function when using the optional
PCB
OLP for booster
heater
Dry contact Vcc-Bit1, Vcc-Bit2 open/short
(System setup necessary)
It is connected to the safety device (OLP) of
DHW tank.
External control
Dry contact Open=not operate, Short=operate
(System setup necessary)
Able to turn ON/OFF the operation by external
switch
Remote controller
Connected (Please use 2 cores wire for relocation
and extension. Total cable length shall be 50m
or less.)
 
Outputs
3-way valve
AC230V N=Neutral Open, Close=direction (For
circuit switching when connected to DHW tank)
2-way valve
AC230V N=Neutral Open, Close (Prevent water
circuit pass through during cooling mode)
Extra pump
AC230V (Used when indoor unit pump capacity is
insuffi cient)
Booster heater
AC230V (Used when using booster heater in DHW
tank)
Boiler contact Dry contact (System setup necessary)
 
Thermistor inputs
Zone 1 room
sensor PAW-A2W-TSRT

It does not work when using
the optional PCB
Outdoor air
sensor AW-A2W-TSOD (Total cable length shall be 30m
or less)
Tank sensor Please use Panasonic specifi ed part
Connection of Optional PCB (CZ-NS4P)
Ext.
comp.
SW
Heat/
Cool
SW
SG
signal
Vcc
Bit1
Bit2
Solar
sensor
Mixing
valve 2 Mixing
valve 1 Optional
Thermostat 2 Optional
Thermostat 1
Demand
signal
Zone 1
water
sensor
Zone 2
water
sensor
Pool
water
sensor
Buffer
Tank
sensor
Zone 1
room
sensor
Zone 2
room
sensor
Zone 1
Pump
Error
signal
Pool
Pump
Solar
Pump
Zone 2
Pump
N O C N O C L N Cool Heat L N Cool Heat
ACXF60-03130_EN ES IT.indb 17 ACXF60-03130_EN ES IT.indb 17 9/22/2016 4:21:32 PM 9/22/2016 4:21:32 PM