background image

ORDER NO. HPD1303U01PE 

 

 

 

Model No.

 EP30006 

Please revise the original parts list in the Service Manual 

ORDER NO. HPD0709C21C1

to conform to the 

change(s) shown herein.

 

If new part numbers are shown, be sure to use them when ordering parts. 

Reason for Change 

*The circled item indicates the reason.    If no marking, see the Notes in the bottom column.

 

1. Improve 

performance 

 

2. 

Change of material or dimension 

 

3. 

To meet approved specification 

 

4. Standardization 

 

5. Addition 

 

6. Deletion 

 

7. 

Correction 

 

8. Other 

 

Interchangeability Code 

**The circled item indicates the interchangeability.    If no marking, see the Notes in the bottom column.

 

 Parts 

 

Set 

Production 

 

Original 

 Early 

New  

Late 

Original or new parts may be used in early or late production set. 
Use original parts until exhausted, then stock new parts. 

Original   Early 

New  

Late 

Original parts may be used in early production sets only.  New parts may be used in early or late 
production sets.    Use original parts where possible, then stock new parts. 

Original   Early 

New  

Late 

New parts only may be used in early or late production sets. 
Stock new parts. 

Original 

 Early 

New  

Late 

Original parts may be used in early production sets only.    New parts may be used in late production 
sets only.    Stock both original and new parts. 

E Other 

 

 

Only

 

replacement

 

part

 

number

 

is

 

changed. 

Part Number

 

Model No. 

Ref. No. 

Original Part No. 

New Part No. 

Notes(*

,

**) 

Part Name & Descriptions 

Remarks 

EP30006 

46 

EP3203K2058W  

WEP3203K2058 

7*,C** 

POWER CORD 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

File this Parts Change Notice with your copy of the Service Manual. 

 

 

 

Содержание Real Pro Ultra EP30006













































































Отзывы: