Panasonic Real Pro Ultra EP30006 Скачать руководство пользователя страница 7

Страница: 7 / 76

EP30006

ORDER NO.HPD0706U16C1

TURNING ON THE POWER

1. Plug the power plug into the power socket.

2. Turn the lock switch to the open position.

3. Turn on the power switch on the back of the unit.

･

When the operating lock switch is pointing toward ‘lock’, the power switch cannot be moved to the ‘on’ position.

Timer

When the on/off button is pushed, a timer begins to prevent overuse. After approximately 15 minutes, time expires and the

massage wheel goes into storage position.

After each use.

･

Be sure to turn the power switch to ‘off’.

･

To prevent children from using this unit,

lock the power switch by moving the operating lock

switch to the ‘lock’ position.

･

As a further caution, unplug the power cord from the power socket after each use.

Содержание Real Pro Ultra EP30006













































































Результаты поиска

Содержание Real Pro Ultra EP30006

Отзывы:

Похожие инструкции для Real Pro Ultra EP30006

Бренды по названию

Популярные бренды

Panasonic Real Pro Ultra EP30006, Руководство по обслуживанию

Результаты поиска

Содержание Real Pro Ultra EP30006

Отзывы:

Похожие инструкции для Real Pro Ultra EP30006

Бренды по названию

Популярные бренды