manualshive.com logo in svg

Panasonic Real Pro Ultra EP30006, Руководство по обслуживанию, Страница: 9 / 76

Поделиться
Скачать
Panasonic Real Pro Ultra EP30006 Скачать руководство пользователя страница 9

EP30006 

ORDER NO.HPD0706U16C1

 

-

 9 

- 

4.

 

ADJUSTMENT OF PRESSURE SENSOR 

 

The adjustment of the Pressure sensor is necessary every time after the Main PCB or Massage mechanism block are 

replaced or repaired disassembled & reassembled. 

First, keep the Massage mechanism block unloaded without pressure and move it upward halfway. 

- If the Massage mechanism block is at the highest or lowest position, you cannot arrange the pressure sensor correctly 

because the fabric becomes tense with pressure. 

 

1.  Insert the Power plug into the power source and turn on the switch of the Power source switch block. 

2.  While pushing the buttons of 

Ⅰ

 and 

Ⅲ

, continue to push the On/off button for more than approximately three seconds.   

Then, the buttons of 

Ⅰ

, 

Ⅲ

, and USER A light. 

3.  In ten seconds after the buttons of 

Ⅰ

, 

Ⅲ

, and USER A light, push the buttons as follows: 

①

SELF PROGRAM

⇒②

LEG/FOOT

⇒③

AUTO WIDTH

⇒④

START 

4.  Push the button of START again, then the adjustment of Pressure sensor finishes. 

5.  Push the button of Stop. 

 

 

Содержание Real Pro Ultra EP30006













































































Отзывы:

Нет отзывов