Panasonic PT-REZ80, Руководство по эксплуатации

Страница: 39 / 313

Chapter 1 Preparation — About your projector
ENGLISH - 39
r
When the SFP modules are installed
This is an example when the SFP module for receiving (LC connector) is installed in the SFP port 1, and the SFP
module for sending and receiving (LC connector) is installed in the SFP port 2.
TY-SB01FB
SIGNAL
SDI OPT
12G/3G/HD
1 IN 2 IN OUT
1 1
2
1 <SDI OPT 1 IN> terminal/<SDI OPT 2 IN> terminal
These are terminals to input SDI signal (optical signal).
2 <SDI OPT OUT> terminal
This is an active through terminal to output the signal that
is input from the <SDI OPT 1 IN> terminal/<SDI OPT 2 IN>
terminal.
Attention
f
The SFP module to be installed on this product is a Class 1 laser product. Do not look into the SFP module or the connector of the optical
fiber cable with the power of the projector turned on. Your eyes may be damaged when the laser goes into your eyes.
Note
f
Depending on the currently selected input, the signal from either the <SDI OPT 1 IN> terminal or the <SDI OPT 2 IN> terminal will be output
from the <SDI OPT OUT> terminal.
f
For details on installing/removing the SFP module, refer to “Installing the SFP module” (
x
page 57) and “Removing the SFP module”
(
x
page 58).
DIGITAL LINK Terminal Board (Model No.: TY-SB01DL)
This board supports the DIGITAL LINK signal.
DIGITAL LINK OUT
LINK
HDCP
POWER
LINK
HDCP
DIGITAL LINK IN
/
LAN
TY-SB01DL
5 2 3 4 3 4 1
1 Power status indicator <POWER>
On:
The power is supplied to the Function Board.
The [DISPLAY OPTION] menu → [SLOT IN] → [DIGITAL LINK
OUT] is set to [ENABLE].
Blinking:
The power is supplied to the Function Board.
The [DISPLAY OPTION] menu → [SLOT IN] → [DIGITAL LINK
OUT] is set to [DISABLE].
Off:
The power is not supplied to the Function Board.
2 <DIGITAL LINK OUT> terminal
This is a terminal to output DIGITAL LINK signal input to the
<DIGITAL LINK IN/LAN> terminal.
3 Signal status indicator <LINK>
On:
DIGITAL LINK signal is input or output.
Blinking:
Only the Ethernet signal is input or output.
Off:
DIGITAL LINK signal is not input or output.
4 Image signal indicator <HDCP>
On:
An image signal protected with HDCP is input or output.
Blinking:
An image signal that is not protected with HDCP is input or
output.
Off:
An image signal is not input or output.
5 <DIGITAL LINK IN/LAN> terminal
This is a terminal to connect a device that transmits an image
signal via the LAN terminal. Also, this is the LAN terminal to
connect to the network.
Note
f
To transmit the Ethernet and serial control signals using the <DIGITAL LINK IN/LAN> terminal, set the [NETWORK] menu → [ETHERNET
TYPE] to [DIGITAL LINK] or [LAN & DIGITAL LINK].
f
To transmit the Ethernet signal using the <LAN> terminal equipped on the projector as standard, set the [NETWORK] menu → [ETHERNET
TYPE] to [LAN] or [LAN & DIGITAL LINK].
f
The <DIGITAL LINK IN/LAN> terminal and the <LAN> terminal equipped on the projector as standard are connected inside of the projector
when the [NETWORK] menu → [ETHERNET TYPE] is set to [LAN & DIGITAL LINK]. Do not directly connect the <DIGITAL LINK IN/
LAN> terminal and the <LAN> terminal using a LAN cable. Construct the system so that it is not connected to the same network via the
peripherals such as the hub or the twisted-pair-cable transmitter.
f
The DIGITAL LINK signal is output only when a display device (projector or flat panel display) that corresponds to any of the following is
connected to the <DIGITAL LINK OUT> terminal.
g
Panasonic Connect Co., Ltd. display device supporting the DIGITAL LINK input
g
Display device installed with the Panasonic Connect Co., Ltd. Function Board supporting the DIGITAL LINK input
f
When the [DISPLAY OPTION] menu → [SLOT IN] → [DIGITAL LINK OUT] is set to [ENABLE] and the projector is in projection mode, the
DIGITAL LINK signal (including the audio signal) input to the <DIGITAL LINK IN/LAN> terminal is output from the <DIGITAL LINK OUT>
terminal.
f
When the projector is in standby mode, the DIGITAL LINK signal input to the <DIGITAL LINK IN/LAN> terminal is not output from the
<DIGITAL LINK OUT> terminal.