background image

8

Y-plan Wiring

PAW cylinders can be

fitted with all types of boilers and

heat pumps operating using room

and cylinder thermostats. Please

follow upper diagram:

‘Wiring for Standard Heat Pump’.

Thermistor controlled Heat

Pumps/Boilers

Many popular Heat pumps now

use a thermistor principle. A

thermistor temperature sensor is

supplied with the Heat Pump to

attach to the cylinder.

Temperature information is

relayed back to the Heat Pump

control system.

A Pocket is provided (see below

to secure the sensor on the

PAW cylinder. The

probe is run through a channel

from base of cylinder to the

immersion housing and housed

there in a pocket. The thermistor

cable should be secured using

the supplied clamps in the bottom

opening of the channel. A

motorised valve must be used in

accordance with Building

Regulation G3. This is wired from

the supplied cylinder thermostat,

wired as high limit stat Please

follow lower diagram:

‘Wiring for Thermistor Controlled

Heat Pump’.

Using Additional Cylinder Thermostat

as high limit stat only:

- coil the grey temperature

probe wire inside additional

cylinder thermostat box and insert

black probe into thermostat pocket

of cylinder then turn dial on front to

number 5

Channel running

from base of cylinder

1

2

E

2

3

1

T6360B

3

3

1

4

G

   

O

    

B1

   

Br

 

G/Y

N

L

E

N

L

E

N

L

ST6400

Heat pump 

Pump

1

 

2

 

3

3

2

3

2

2

2

3

1

V4043H

Room 
thermostat

Zone Valve (DHW)

(supplied)

Isolated Mains
Supply From
Fused Spur

Mid Position Valve

(not supplied)

L

    

N

     

E

6

G/Y

   

B1

   

W

    

Gr

   

O

3

 

2

V4073A1039

10

4

5

9

8

7

Cylinder 

Thermostat

 (supplied)

N    L

C  NC NO

Thermistor

1

2

E

2

3

1

T6360B

3

3

1

4

G

     

O

    

B1

      

Br

   

G/Y

N

L

E

N

L

E

N

L

ST6400

Heat pump differential controler

Pump

1

 

2

 

3

3

2

3

2

2

2

3

1

V4043H

Room 

thermostat

Zone Valve (DHW)
(supplied)

Isolated Mains
Supply From
Fused Spur

Mid Position Valve

(not supplied)

L

     

N

     

E

6

G/Y

      

B1

    

W

     

Gr

     

O

3

 

2

V4073A1039

10

4

5

9

8

7

 Cylinder 

Thermostat

 (supplied ) 

wired as high limit Stat

N    L

C  NC NO

Thermistor wire 
Connected to 

Heat pump 

control 

system

Pump 
flow

2-port valve

(supplied)

Mid pos. valve
(not supplied)

Radiators/

UFH

HP/Boiler

Automatic
bypass

Piping 
Diagram

HW

ON

HW

OFF

HTG

ON

HW

ON

HW

OFF

HTG

ON

Programmer

Programmer

Wiring for Standard Heat pump

Wiring for Thermistor Controlled Heat Pump

Содержание PAW-TD20C1E5-UK

















Отзывы: