RQTV0115
12
12
Tuning the TV to Your Unit
The unit supplies a signal to the TV via the RF coaxial cable on
channel E21
s
E69. It is possible to view the unit’s picture on your TV
in the same way that you watch TV broadcasts. The unit is fitted with
its own tuner (just like a normal TV) and can be preset to receive up
to 99 TV broadcast stations.
≥
Press
[VHS SELECT]
(
l
8).
¬
If you have connected the unit to the TV through the audio/
video output sockets
You do not need to follow the procedure below. To view the pictures
from the unit, set to the AV mode on the TV with
[AV]
.
When the unit is turned on after
connecting the aerial cable and the
mains lead for the first time, tuning
starts automatically.
≥
If the unit is turned on with the aerial not
connected, all channels are skipped.
.................................................................................................................................
[1]
Press [
Í
VHS] to turn on
this unit.
.................................................................................................................................
[2]
Set the TV to an unused
position for the unit
viewing channel.
≥
Tune the TV until the display shown
on the right appears. Refer also to
the TV’s instructions regarding tuning.
≥
Set “RF SELECT” by pressing
[
2 1
]
to select the colour TV
system used by the TV set to be connected.
BG:
PAL B.G.H/SECAM B.G
I:
PAL I
DK:
PAL D/SECAM D.K.K1
.........................................................................................................................................................................................................................
[3]
Press [MENU].
ª
To cancel Auto Tuning halfway through
Auto Tuning will stop halfway by turning the unit off, pressing
[MENU]
,
playback or power failure.
¬
If Auto Tuning stops halfway by turning the unit off, playback
or power failure
≥
Disconnect the mains lead and then reconnect it.
≥
Turn on the unit. Plug in Auto Tuning restarts.
¬
To set the channels manually (
l
20)
ª
To restart Plug in Auto Tuning
≥
Turn the unit on.
≥
Make sure there is no video cassette in
the unit.
1) Keep
both
[
I
CH]
and [
J
CH] on
the unit pressed simultaneously for
3 seconds or more until the channel
on the unit’s display changes to 1.
2) Disconnect the mains lead and then reconnect it.
3) Turn on the unit. Plug in Auto Tuning restarts.
You can change the RF output channel, for example, when
interference occurs on the picture after tuning.
.........................................................................................................................................................................................................................
[1] Press [MENU] for 5
seconds or more.
.................................................................................................................................
[2] Press [
J
CH] or [
I
CH]
to select the channel
(E21
s
E69).
≥
Each time you press
[
J
CH]
or
[
I
CH]
, (
l
below).
≥
Set to “
ss
” (RF OFF) when you
use the Audio/Video cable for the
connection.
≥
You can also use the numeric
buttons.
Example: “28”; [2]
l
[8]
.............................................................................................
[3] Retune your TV to
the new RF channel
for the unit.
.............................................................................................
[4] Press [MENU] to exit
the setting mode.
Note:
≥
Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
Plug in Auto Tuning
RF SELECT :
END : MENU
CH 22
SEARCH
21
END : MENU
AUTO TUN I NG S
COMPLETED .
RF SELECT
BG DK
Disappears
1
To Change the RF Output Channel
RF SELECT :
END : MENU
RF SELECT
BG
DK
I
Panasonic
21
6
9
(RF OFF)
VP60GCS.book Page 12 Monday, March 6, 2006 3:23 PM
