manualshive.com logo in svg

Panasonic M1S Series, Руководство по эксплуатации

Поделиться
Скачать
Panasonic M1S Series Скачать руководство пользователя страница 16

‑ 16 ‑

System Configuration and Wiring

Precautions when wiring

The inner circuit is still energized with a high voltage after the input power is turned off.    Do
not touch the inverter for at least 5 minutes after turning off the power.

 Main circuit

(1) The inverter will be damaged if you invert the connections of the power input terminal

and motor output terminal (U/L1, V/L2, W/L3). Absolutely do not invert connections.

(2) Do not ground the main circuit terminal.
(3) Do not short motor output terminals (U/L1, V/L2, W/L3) together.
(4) The GND terminal (E) is the frame ground (FG) for the inverter.
(5) Be sure to use insulated crimp terminals for connecting to the main circuit terminals.

 Control circuit

(1) Use the wires with the insulation removed, as shown below, to wire the control circuit.

If the exposed area is too long, there is the possibility of a short occurring with the
adjacent wire.    If it is too short, the wire could be pulled. Twist the bare wires when
wiring, so that they will not get loose.

(2) Use a wire which diameter is less than 0.9 mm when wiring using a bar terminal or single

wire.    If it is larger than 0.9 mm, the screw thread may be damaged when tightened.

(3)  Do not apply more than 24VDC, 50mA to the output terminals (O1, C1), or apply

voltage to terminal in reverse.

(4) Input terminal configuration is internally pulled up from approx. +12V by approx. 3.3k

Ω

.

You can control by contact or by open collector output. Do not apply external voltage.

                          NPN logic                                                                PNP logic

(5) Do not short the frequency setting power source terminal (5V) and ground for control

terminal (G).

(6) To directly drive the relay by the output terminals (O1, C1), mount a flywheel diode (FD).

(7) Use shielded wires for the cable to be connected to the control circuit.

ＦＤ（１００Ｖ

 

１Ａ）

Ｒ Ｙ

Ｃ

1

O1

<Examples>  Fuji Electric  ERA15-01

ERB12-01

Pay attention to polarity of diode.

Photo coupler

5.5 mm ± 1 mm

power
source

I

1 ~ 

I

5

+12V

Internal circuits of I1 – I5 are as follows:

G

I

1 ~ 

I

5

+12V

Internal circuits of I1 – I5 are as follows:

+12V

power
source

Содержание M1S Series





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды