Panasonic Lumix DMC-G1KPP, Руководство по обслуживанию

Страница: 57 / 79

S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Flash P.C.B. .......................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Schematic Diagram ..................................................... S-5
S4.3. AF Assist Schematic Diagram ............................................... S-6
S4.4. LP SW Schematic Diagram ................................................... S-6
S4.5. Remote Schematic Diagram ................................................. S-7
S4.6. LCD IF Schematic Diagram .................................................. S-7
S4.7. Hinge SW Schematic Diagram.............................................. S-8
S4.8. Flash Sub Schematic Diagram.............................................. S-8
S5. Print Circuit Board .................................................................... S-9
S5.1. Flash P.C.B. .......................................................................... S-9
S5.2. AF Assist P.C.B. .................................................................. S-10
S5.3. LP SW P.C.B. ...................................................................... S-10
S5.4. Remote P.C.B. ..................................................................... S-11
S5.5. LCD IF P.C.B. ...................................................................... S-12
S5.5.1. LCD IF P.C.B. (Component Side) ..................................... S-12
S5.5.2. LCD IF P.C.B. (Foil Side) ................................................. S-13
S5.6. Hinge SW P.C.B. ................................................................. S-14
S5.7. Flash Sub P.C.B. ................................................................. S-14
S6. Replacement Parts List .......................................................... S-15
S7. Exploded View ....................................................................... S-21
S7.1. Frame and Casing Section.................................................. S-21
S7.2. Camera Lens Section.......................................................... S-22
S7.3. Packing Parts and Accessories Section .............................. S-23
Table of contents
Service Manual
DSC0810042CE
Diagrams and Replacement
Parts List
Vol. 1
(A)...........Blue Type
Colour
(R)...........Red Type
Model No.
DMC-G1KPP
DMC-G1KEB
DMC-G1KEC
DMC-G1KEG
DMC-G1KGC
DMC-G1KGD
DMC-G1KGH
DMC-G1KGK
DMC-G1KGN
DMC-G1KGT
DMC-G1KGJ
Digital Camera
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice