background image

82

new:
DIN 48 SIZE
LCD ELECTRONIC COUNTER
Scale factor, power supply

LC4H-S

NEW FEATURES:

1. Scale Factor:

A scale factor can be entered into LC4H-SV
series. After that one count shows the real
unit/value of the machine/application.

2. 12 V DC Power Supply:

The 100 – 240 V AC types are equipped 

with a 12 V DC power supply 100 mA. 
It is possible to connect photo-sensors,
proximity switches or encoders without addi-
tional devices.

3. Voltage Signal Input:

PNP input types are available.

FEATURES

1. Bright and Easy-to-Read Display

A brand new bright 2-color backlight LCD
display. The easy-to-read screen in any
location makes checking and setting pro-
cedures a cinch.

2. Simple Operation

Seesaw buttons make operating the unit
even easier than before.

3. Conforms to IP66’s Weather
Resistant Standards

The water-proof panel keeps out water
and dirt for reliable operation even in
poor environments.

4. Screw terminal and Pin Type are
Both Standard Options

The two terminal types are standard
options to support either front panel
installation or embedded installation.

5. 4-digit or 6-digit display

Two sizes of displays are offered for you
to choose the one that suits your needs.

6. Conforms With EMC and Low
Voltage Directives

Conforms with EMC directives
(EN50081-2/EN50082-2) and low-volt-
age directives (VDE0435/Part 2021) for
CE certification vital for use in Europe.

R4 / T4 systems (4-digit display)

R6 / T6 systems (6-digit display)

Pin type

Screw terminal type

PRODUCT TYPES

LC4H-SV

* A rubber gasket (ATC18002) and a mounting frame (AT8-DA4) are included.

mm 

inch

Digit

Count speed

Output

Operation voltage

Power down

Additional function

Terminal

P/N

insurane

Scale Factor

11 Pin

LC4H-PS-R4-AC240V

100-240 V AC

Scale Factor

Screw

LC4H-PS-R4-AC240VS

with 12V DC power supply

Scale Factor / Voltage Signal Input

11 Pin

LC4H-PSV-R4-AC240V

Relay

Scale Factor / Voltage Signal Input

Screw

LC4H-PSV-R4-AC240VS

Scale Factor

11 Pin

LC4H-S-R4-24V

4

Scale Factor

Screw

LC4H-S-R4-24VS

Scale Factor / Voltage Signal Input

11 Pin

LC4H-SV-R4-24V

12-24 V DC / 24 V AC

Scale Factor / Voltage Signal Input

Screw

LC4H-SV-R4-24VS

Scale Factor

11 Pin

LC4H-S-T4-24V

Transistor

Scale Factor

Screw

LC4H-S-T4-24VS

30 Hz (cps)

Scale Factor / Voltage Signal Input

11 Pin

LC4H-SV-T4-24V

5 kHz (kcps)

Available

Scale Factor / Voltage Signal Input

Screw

LC4H-SV-T4-24VS

switchable

Scale Factor

11 Pin

LC4H-PS-R6-AC240V

100-240 V AC

Scale Factor

Screw

LC4H-PS-R6-AC240VS

with 12V DC power supply

Scale Factor / Voltage Signal Input

11 Pin

LC4H-PSV-R6-AC240V

Relay

Scale Factor / Voltage Signal Input

Screw

LC4H-PSV-R6-AC240VS

Scale Factor

11 Pin

LC4H-S-R6-24V

Scale Factor

Screw

LC4H-S-R6-24VS

6

Scale Factor / Voltage Signal Input

11 Pin

LC4H-SV-R6-24V

12-24 V DC / 24 V AC

Scale Factor / Voltage Signal Input

Screw

LC4H-SV-R6-24VS

Scale Factor

11 Pin

LC4H-S-T6-24V

Transistor

Scale Factor

Screw

LC4H-S-T6-24VS

Scale Factor / Voltage Signal Input

11 Pin

LC4H-SV-T6-24V

Scale Factor / Voltage Signal Input

Screw

LC4H-SV-T6-24VS

48

1.890

48

1.890

64.5

2.539

02/2003

Содержание LC4H-S












Отзывы: