Panasonic KX-TCD965EC Скачать руководство пользователя

Страница: 12 / 84

Connections

Plug in the AC adaptor cord and the telephone line cord to the bottom of the unit. Then connect
the cords as shown.

•

USE ONLY WITH Panasonic AC ADAPTOR KX-TCA11E.

•

Be careful not to confuse the telephone line jack with the AC adaptor jack on the base unit. If
connected improperly, the base unit will not work and damage may occur.

•

The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during
use.)

•

To connect a standard telephone on the same line, see page 81.

•

If your unit is connected to a PBX which does not support Caller ID services, you cannot access
those services.

CONNECTION OF POWER SUPPLY

This apparatus is intended for use when powered by the KX-TCA11E.
Using other power supplies will invalidate any approval given to this apparatus.

Telephone
Line Cord

AC
Adaptor

Fasten the cords to prevent them from
being disconnected.

Hooks

Telephone Line Cord

AC Adaptor

To Mains Outlet
(AC 230– 240 V, 50 Hz)

To B.T. Socket

Settings

TNV*

*The abbreviation TNV means

“Telephone Network Voltage”.

KX-TCD965EC-1(2~25) 99.9.27 8:05 PM Page 12

Содержание KX-TCD965EC





















































































Результаты поиска

Содержание KX-TCD965EC

Отзывы:

Похожие инструкции для KX-TCD965EC

Бренды по названию

Популярные бренды

Panasonic KX-TCD965EC, Руководство по эксплуатации

Результаты поиска

Содержание KX-TCD965EC

Отзывы:

Похожие инструкции для KX-TCD965EC

Бренды по названию

Популярные бренды