Panasonic KX-T30865 Скачать руководство пользователя страница 69

Страница: 69 / 176

2.5 Installation of the Other Cards

Installation Manual

2.5

Installation of the Other Cards

2.5.1

DPH4 Card

Function

4-port doorphone card for 4 doorphones, 4 door openers (relays) and 4 sensors.

Accessory and User-supplied Items

User-supplied (not included): none

Notice

The connector type may be RJ45 or RJ11 depending on the country/area.

Shown above is a card having the RJ45 connectors. As compared to the RJ45 connectors,
the RJ11 connectors are upside down in position.

Note

For details about connection to doorphones and door openers, refer to "2.9.1 Connection
of Doorphones and Door Openers".

Accessory (included): Extension Bolt

1, 10-pin terminal block

1, 8-pin terminal block

1, Telephone Line Cord

2, Terminal Box

1 (for DPH4 card with

RJ45 connectors) or 2 (for DPH4 card with RJ11 connectors) , Strap

To sensors

To doorphones

To door openers

Telephone Line Cord

8-pin

10-pin

Содержание KX-T30865

















































































































































































Результаты поиска

Содержание KX-T30865

Отзывы:

Бренды по названию

Популярные бренды

Panasonic KX-T30865, Руководство по установке

Результаты поиска

Содержание KX-T30865

Отзывы:

Бренды по названию

Популярные бренды