manualshive.com logo in svg

Panasonic KX-T30865, Руководство по установке

Поделиться
Скачать
Panasonic KX-T30865 Скачать руководство пользователя страница 134

2.10 Connection of Peripherals

134

Installation Manual

2.10 Connection of Peripherals

2.10.1 Connection of Peripherals

BGM/MOH

The Hybrid IP-PBX provides Background Music and Music on Hold. Only 1 external music 
source (e.g., user-supplied radios) can be used by connecting them to the Hybrid IP-PBX.

CAUTION

•

Wiring should be done carefully to prevent undue force being exerted on the plug. 
Otherwise, music may intermittent.

•

External Music Jack is SELV port and should only be connected to approved SELV 
devices, or in Australia, via the Line Isolation Unit with the Telecommunications 
Compliance Label.

Note

When the Hybrid IP-PBX and external music sources are not connected to the same 
earth, hum noise may be induced into Background Music and Music on Hold.

BGM/
Music on Hold

Pager:
Amplifier/Speaker

PC

Printer

PC

Diameter       Maximum Distance
0.4 mm:        Under 10 m
0.5 mm:        Under 10 m
0.6 mm:        Under 10 m

Diameter       Maximum Distance
0.4 mm:        Under 10 m
0.5 mm:        Under 10 m
0.6 mm:        Under 10 m

                     Maximum Distance
                     Under 2 m

                     Maximum Distance
                     Under 5 m

Содержание KX-T30865

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды