Panasonic KX-T30865 Скачать руководство пользователя страница 12

Страница: 12 / 176

Installation Manual

Table of Contents

System Outline .............................................................................. 15

1.1

System Highlights ................................................................................................. 16

1.1.1

System Highlights.................................................................................................... 16

1.2

Basic System Construction.................................................................................. 18

1.2.1

Main Unit ................................................................................................................. 18

1.2.2

System Connection Diagram................................................................................... 19

1.3

Options................................................................................................................... 21

1.3.1

Options .................................................................................................................... 21

1.4

Specifications ........................................................................................................ 23

1.4.1

General Description................................................................................................. 23

1.4.2

Characteristics......................................................................................................... 25

1.4.3

System Capacity ..................................................................................................... 26

Installation ..................................................................................... 29

2.1

Before Installation ................................................................................................. 30

2.1.1

Before Installation.................................................................................................... 30

2.2

Installation of the Hybrid IP-PBX ......................................................................... 32

2.2.1

Unpacking ............................................................................................................... 32

2.2.2

Names and Locations.............................................................................................. 33

2.2.3

Opening/Closing the Covers ................................................................................... 34

2.2.4

Installation of the SD Memory Card ........................................................................ 38

2.2.5

Frame Earth Connection ......................................................................................... 39

2.2.6

Backup Batteries Connection .................................................................................. 40

2.2.7

Installing/Removing the Optional Service Cards ..................................................... 41

2.2.8

Types of Connectors................................................................................................ 44

2.2.9

Wall Mounting (KX-TDA30) ..................................................................................... 46

2.2.10 Wall Mounting (AC Adaptor).................................................................................... 48
2.2.11 Lightning Protector Installation ................................................................................ 50
2.3

Installation of the Trunk Cards............................................................................. 53

2.3.1

LCOT4 Card ............................................................................................................ 53

2.3.2

CID4 Card ............................................................................................................... 55

2.3.3

BRI2 Card................................................................................................................ 56

2.3.4

IP-GW4 Card........................................................................................................... 59

2.4

Installation of the Extension Cards ..................................................................... 61

2.4.1

DLC4 Card .............................................................................................................. 61

2.4.2

SLC4 Card............................................................................................................... 63

2.4.3

DLC8 Card .............................................................................................................. 65

2.4.4

SLC8 Card............................................................................................................... 67

2.5

Installation of the Other Cards............................................................................. 69

2.5.1

DPH4 Card .............................................................................................................. 69

2.5.2

DPH2 Card .............................................................................................................. 72

2.5.3

ECHO8 Card ........................................................................................................... 75

2.5.4

MSG2 Card ............................................................................................................. 76

2.5.5

EXT-CID Card.......................................................................................................... 77

2.5.6

RMT Card................................................................................................................ 78

2.6

Connection of Extensions .................................................................................... 79

2.6.1

Maximum Cabling Distance of the Extension Wiring (Twisted Cable) ..................... 79

Содержание KX-T30865

















































































































































































Результаты поиска

Содержание KX-T30865

Отзывы:

Бренды по названию

Популярные бренды

Panasonic KX-T30865, Руководство по установке

Результаты поиска

Содержание KX-T30865

Отзывы:

Бренды по названию

Популярные бренды